HP Visualize c3000 hp Visualize b1000 and c3000 workstations owner's guide (a5 - Page 207

Dealing with a Boot Failure

Get HP Visualize c3000 - Workstation PDF manuals and user guides View all HP Visualize c3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 207 highlights

NOTE NOTE Solving Problems Dealing with a Boot Failure Dealing with a Boot Failure If your usual boot device (typically a disk) is not responding as it should, you must try to boot from the disk (or another boot device) by selecting it manually. Note that you must be superuser (root) to perform the steps in this section. To boot a device manually, follow these steps: A common cause of boot failures is forgetting to connect your Ultra2 Wide Low-Voltage Differential SCSI terminator and your Fast Narrow Single-Ended SCSI terminator to their connectors on the back of your system unit. Note that these terminators were shipped with your system unit. 1. Follow the directions in "Accessing the Boot Console Interface," in Chapter 6 of this document. Your computer automatically shuts down the operating system before it terminates the power. 2. At the Main Menu prompt, type the following and press Enter: Main Menu: Enter command > search ipl This causes you computer to search exhaustively for bootable media. 3. Boot from one of the listed devices by typing the following at the prompt and press Enter: Main Menu: Enter command > boot device where device is the hardware path to the device, specified in mnemonic style notation, such as FWSCSI.5.0. 4. Answer "N" to the question, INTERACT WITH IPL (Y,N,Q)? Chapter 7 207

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
Chapter 7
207
Solving Problems
Dealing with a Boot Failure
Dealing with a Boot Failure
If your usual boot device (typically a disk) is not responding as it should,
you must try to boot from the disk (or another boot device) by selecting it
manually. Note that you must be superuser (
root
) to perform the steps
in this section.
To boot a device manually, follow these steps:
NOTE
A common cause of boot failures is forgetting to connect your Ultra2
Wide Low-Voltage Differential SCSI terminator and your Fast Narrow
Single-Ended SCSI terminator to their connectors on the back of your
system unit. Note that these terminators were shipped with your system
unit.
1.
Follow the directions in “Accessing the Boot Console Interface,” in
Chapter 6 of this document.
NOTE
Your computer automatically shuts down the operating system before it
terminates the power.
2.
At the Main Menu prompt, type the following and press
Enter
:
Main Menu: Enter command > search ipl
This causes you computer to search exhaustively for bootable media.
3.
Boot from one of the listed devices by typing the following at the
prompt and press
Enter
:
Main Menu: Enter command > boot
device
where
device
is
the
hardware
path
to
the
device,
specified
in
mnemonic style notation, such as
FWSCSI.5.0
.
4.
Answer “
N
” to the question,
INTERACT WITH IPL (Y,N,Q)?