Hitachi NT65GS Instruction Manual - Page 24

Loading Nails - nt65ga

Get Hitachi NT65GS - 2-1-2inch 16 Gauge Gas Powered Straight Finish Nailer PDF manuals and user guides
UPC - 717709010864
View all Hitachi NT65GS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English 4 Close the actuator. 2. Push down 1. Swing back (7) If no abnormal operation is observed, you may load nails in the Nailer. Drive nails into the workpiece that is the same type to be used in the actual application. Ⅺ THE NAILER MUST OPERATE PROPERLY. (4) Remove the finger from the trigger and press the push lever against the workpiece with pulling back the nail feeder (B). (NT50GS: Unnecessary to pulling back nail feeder) Ⅺ THE NAILER MUST NOT OPERATE. Do not pull trigger LOADING NAILS WARNING ⅷ When loading nails into Nailer, 1) do not pull trigger; 2) do not depress push lever; and 3) keep Nailer pointed downward. 2-Action Nail Feeding! (1) Insert nail strip into the back of the magazine. Depress push lever Nail feeder (B) (5) Separate the push lever from the workpiece. Next, point the nailer downward, pull the trigger and then wait in that position for 5 seconds or longer. Ⅺ THE NAILER MUST NOT OPERATE. Magazine (2) Slide the nail strip forward in the magazine. Pull trigger (6) Without touching the trigger, depress the push lever against the workpiece. Pull the trigger. Ⅺ THE NAILER MUST OPERATE. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
English
24
4
Close the actuator.
(4) Remove the finger from the trigger and
press the push lever against the
workpiece with pulling back the nail
feeder (B). (NT50GS: Unnecessary to
pulling back nail feeder)
³
THE NAILER MUST NOT OPERATE.
(5) Separate the push lever from the
workpiece.
Next, point the nailer downward, pull the
trigger and then wait in that position for
5 seconds or longer.
³
THE NAILER MUST NOT OPERATE.
(6)
Without touching the trigger, depress the
push lever against the workpiece.
Pull the trigger.
³
THE NAILER MUST OPERATE.
1. Swing back
2. Push down
Depress push lever
Nail feeder (B)
Do not pull trigger
Pull trigger
(7)
If no abnormal operation is observed, you
may load nails in the Nailer.
Drive nails into the workpiece that is the
same type to be used in the actual
application.
³
THE NAILER MUST OPERATE
PROPERLY.
LOADING NAILS
WARNING
²
When loading nails into Nailer,
1)
do not pull trigger;
2)
do not depress push lever; and
3)
keep Nailer pointed downward.
<NT65GS, NT65GA, NT65GB>
2–Action Nail Feeding!
(1) Insert nail strip into the back of the
magazine.
(2) Slide the nail strip forward in the
magazine.
Magazine