Hitachi NT65MA3 Instruction Manual - Page 6

Explanation of the Nailing Operation, A FULL SEQUENTIAL ACTUATION MECHANISM KIT SEQUENTIAL TRIP

Get Hitachi NT65MA3 - 2-1/2 Angled Finish Nailer PDF manuals and user guides
UPC - 717709011281
View all Hitachi NT65MA3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

5-2. Explanation of the Nailing Operation To meet the requirements of "ANSI SNT-101-2002", the Model NT 65MA3 is equipped with a nailing operation switching device at the valve section as shown in the figures below. Use SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM) or CONTACT ACTUATION MECHANISM in accordance with the work to be performed. A FULL SEQUENTIAL ACTUATION MECHANISM KIT (SEQUENTIAL TRIP MECHANISM KIT) is also available as an option. Each nailing operation is as follows. SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM): First, press the pushing lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next, press the pushing lever against the wood to drive the nail. After nailing once, nailing will not be possible again until the trigger is released and pressed again. CONTACT ACTUATION MECHANISM: First, press the pushing lever against the wood; next, pull the trigger to drive the nail. First, pull the trigger; next, press the pushing lever against the wood to drive the nail. If the trigger is held back, a nail will be driven each time the pushing lever is pressed against the wood. FULL SEQUENTIAL ACTUATION MECHANISM: First, press the pushing lever against the wood; next, pull the trigger to drive the nail. Follow the same sequence to continue driving nails. Nailing operation switching device Switching device (Change knob) Switching device (Change knob) SINGLE ACTUATION MECHANISM (Switching device: upward position) CONTACT ACTUATION MECHANISM (Switching device: downward position) --- 3 ---

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
--- 3 ---
5-2. Explanation of the Nailing Operation
To meet the requirements of "ANSI SNT-101-2002", the Model NT 65MA3 is equipped with a nailing operation
switching device at the valve section as shown in the figures below.
Use SINGLE ACTUATION MECHANISM
(SINGLE SEQUENTIAL ACTUATION MECHANISM) or CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
A FULL SEQUENTIAL ACTUATION MECHANISM KIT (SEQUENTIAL TRIP
MECHANISM KIT) is also available as an option.
Each nailing operation is as follows.
SINGLE ACTUATION MECHANISM (SINGLE SEQUENTIAL ACTUATION MECHANISM):
First, press the pushing lever against the wood; next, pull the trigger to drive the nail.
First, pull the trigger;
next, press the pushing lever against the wood to drive the nail.
After nailing once, nailing will not be possible
again until the trigger is released and pressed again.
CONTACT ACTUATION MECHANISM:
First, press the pushing lever against the wood; next, pull the trigger to drive the nail.
First, pull the trigger;
next, press the pushing lever against the wood to drive the nail.
If the trigger is held back, a nail will be driven
each time the pushing lever is pressed against the wood.
FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the pushing lever against the wood; next, pull the trigger to drive the nail.
Follow the same
sequence to continue driving nails.
Nailing operation switching device
SINGLE ACTUATION
MECHANISM
(Switching device:
upward position)
CONTACT ACTUATION
MECHANISM
(Switching device:
downward position)
Switching device
(Change knob)
Switching
device
(Change
knob)