Honeywell HJC5000 User Guide - Page 54

Step 2: Con the Controller for MAXPRO Mode, Step 3: Con Address, Baud Rate

Get Honeywell HJC5000 PDF manuals and user guides View all Honeywell HJC5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Installing UltraKey Lite with MAXPRO-Net Step 2: Configure the Controller for MAXPRO Mode Note The controller factory defaults to VideoBloX mode, Address 1, baud rate 19200 bps. 1. If not already done, install and connect the controller to a power source. The UltraKey Lite LCD displays. 2. From the home screen, press Alt > Clr to enter the System Configuration: System Set menu. 3. Enter the PIN password 3434. The System Set: Mode screen displays. 4. Press the LCD right arrow key to enter the Mode Selection menu. 5. Scroll to and select MAXPRO. Press Ent. 6. From the home screen, press Alt > Clr to enter the System Configuration: System Set menu. The System Set: Mode screen displays. 7. Press the LCD right arrow key to enter the Mode Selection menu. 8. Scroll to and select MAXPRO. Press Ent. MAXPRO Loading displays and one of two screens display: Maxpro Loading. • If the controller is able to connect to the MAXPRO network, the LCD displays the connection, for example, fixed camera 1 has sent a signal from MAXPRO to the controller. • If the controller is not able to connect to the MAXPRO network, the offline menu displays If this menu displays, you cannot configure the serial or ethernet connections in the next step. FIXED CAMERA Camera 1 Maxpro offline Keyboard 1 Step 3: Configure Address, Baud Rate, or IP for MAXPRO-Net mode 1. Press Alt > Clr. If prompted, enter the password 3434 to enter the System Setup: Config menu. 2. Press the right LCD arrow key to enter the Configuration menus. System Set: CONFIG 3. Press the LCD up/down arrow keys to scroll through the options (restore default, VB settings, maxpro settings, network, language, back light, slider update, hardware test, Configuration Maxpro Settings about). Scroll to the Configuration: Maxpro settings menu, then press Ent. 4. Select By Serial Port from the MAXPRO connection submenu, then press Ent. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
54
Installing UltraKey Lite with MAXPRO-Net
Step 2: Configure the Controller for MAXPRO Mode
Note
The controller factory defaults to VideoBloX mode, Address 1, baud rate
19200 bps.
1.
If not already done, install and connect the controller to a power source.
The UltraKey Lite LCD displays.
2.
From the home screen, press
Alt > Clr
to enter the
System Configuration: System
Set
menu.
3.
Enter the PIN password
3434
.
The
System Set: Mode
screen displays.
4.
Press the LCD right arrow key to enter the
Mode Selection
menu.
5.
Scroll to and select
MAXPRO
. Press
Ent
.
6.
From the home screen, press
Alt > Clr
to enter the
System Configuration: System
Set
menu.
The
System Set: Mode
screen displays.
7.
Press the LCD right arrow key to enter the
Mode Selection
menu.
8.
Scroll to and select
MAXPRO
. Press
Ent
.
MAXPRO
Loading
displays and one of two screens display:
•
If the controller is able to connect to the MAXPRO
network, the LCD displays the connection, for example,
fixed camera 1
has sent a signal from MAXPRO to
the controller.
•
If the controller is not able to connect to the MAXPRO
network, the offline menu displays If this menu
displays, you cannot configure the serial or ethernet
connections in the next step.
Step 3: Configure Address, Baud Rate, or IP for MAXPRO-Net mode
1.
Press
Alt > Clr
. If prompted, enter the password
3434
to
enter the
System Setup: Config
menu.
2.
Press the right LCD arrow key to enter the
Configuration
menus.
3.
Press the LCD up/down arrow keys to scroll through the
options (restore default, VB settings, maxpro settings,
network, language, back light, slider update, hardware test,
about).
Scroll to the
Configuration: Maxpro settings
menu, then press
Ent
.
4.
Select
By Serial Port
from the MAXPRO connection submenu, then press
Ent
.
Maxpro Loading.
FIXED CAMERA
Camera 1
Maxpro offline
Keyboard
1
System Set:
CONFIG
Configuration
Maxpro Settings