Honeywell HJK7000 User Guide - Page 35

Installing and Configuring an Ethernet Connection, Step 1: Connect to the UltraKey Plus Ethernet Port

Get Honeywell HJK7000 PDF manuals and user guides View all Honeywell HJK7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

UltraKey Plus Controller Installation and User Guide Installing and Configuring an Ethernet Connection For a list of accessories see Shipping Checklist on page 18 and for port connections and pin assignments see UltraKey Plus Port Connections and Descriptions on page 19. The UltraKey Plus Controller runs TCP/IP keyboard protocol. Step 1: Connect to the UltraKey Plus Ethernet Port Note The direct RJ45 connection using the Ethernet port is only available with newer model VideoBloX NetCPU systems. Table 2-2 RJ45 Ethernet Pin Assignments Port Pin RJ45 Ethernet 1 2 3 6 Signal TX + TX RX+ RX- To connect to the UltraKey Plus Ethernet port: 1. Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place. See Figure 2-2. 2. Plug the AC adapter into the controller power port and the adapter into a power source. 3. Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 32 controllers can be connected to the network. See Figure 2-6. 4. Connect VideoBloX to the network. Refer to the applicable VideoBloX Installation Guide for instructions. Document 800-02573 Rev B 35 11/2009

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
UltraKey Plus Controller Installation and User Guide
Document 800-02573 Rev B
35
11/2009
Installing and Configuring an Ethernet Connection
For a list of accessories see
Shipping Checklist
on page
18
and for port connections and
pin assignments see
UltraKey Plus Port Connections and Descriptions
on page
19
. The
UltraKey Plus Controller runs TCP/IP keyboard protocol.
Step 1: Connect to the UltraKey Plus Ethernet Port
Note
The direct RJ45 connection using the Ethernet port is only available with
newer model VideoBloX NetCPU systems.
To connect to the UltraKey Plus Ethernet port:
1.
Select the applicable adapter plug and insert it into the AC adapter. Push to click it
into place. See
Figure 2-2
.
2.
Plug the AC adapter into the controller power port and the adapter into a power
source.
3.
Plug an RJ45 network cable from the network to the controller Ethernet port. Up to 32
controllers can be connected to the network. See
Figure 2-6
.
4.
Connect VideoBloX to the network. Refer to the applicable
VideoBloX Installation
Guide
for instructions.
Table 2-2
RJ45 Ethernet Pin Assignments
Port
Pin
Signal
RJ45 Ethernet
1
TX +
2
TX -
3
RX+
6
RX-