Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 535 AWD » Manual Viewer

Husqvarna AUTOMOWER 535 AWD Owner Manual - Page 26

To start to use Automower® Direct, User interface overview, To start the product for the first time

View all Husqvarna AUTOMOWER 535 AWD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

3.10.5.1 To start to use Automower® Direct 1. Download the Automower® Connect app on your mobile device. 2. Select Automower® Direct on the start screen of the Automower® Connect app. 3. Start Bluetooth® on your mobile device and on the product, refer to To start the product for the first time on page 26. 4. Go to the Settings symbol in the display and activate Bluetooth®. 5. Select the product to pair with in the Automower® Connect app. 6. Enter the PIN code for the product. Note: You have access to the menus and functions as long as you are in Bluetooth® shortrange. 3.10.6 User interface overview The user interface overview below shows examples of Automower® Connect. Automower® Connect My Automower R My Automower R My Automower R My Automower R 6 MOWING Mowing session ends 13:30 PARK Schedule PAUSE Map 6 PARKED Next start tomorrow 16:30 PARK Schedule START Map 6 PAUSED PARK Schedule START Map 6 ERROR Charging station Blocked MORE DETAILS Schedule Map 3.11 To start the product for the first time When the product is switched on for the first time, there are some basic settings to do before the product can start to operate. 1. Push the ON/OFF button for 3 seconds to switch on the product. Note: The Bluetooth® pairing mode is on for 3 minutes and the LED light is flashing blue. If the product does not pair with Bluetooth® in 3 minutes, switch off the product. Wait until the LED status indicator is not lit, and then switch on the product again. 2. Enter the factory PIN code. 3. Log on to your Husqvarna account in the Automower® Connect app to pair your product with Automower® Connect. Note: It is recommended to pair your product with Automower® Connect to get access to all functions in the product. If it is not necessary to pair your product with Automower® Connect, push the arrow symbol to continue to the menu. 4. Start Bluetooth® on your mobile device. 5. Select My mowers in the Automower® Connect app, and then select the plus sign (+). 6. Select model. The Automower® Connect app searches for available products within short-range (Bluetooth®). 26 - Installation 1427 - 002 - 20.12.2019

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the battery	6
General safety instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
LED status indicator	10
Safety	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	11
Safety definitions	12
Safety instructions for operation	12
Use	12
Battery safety	13
How to lift and move the product	14
Maintenance	14
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Main components for installation	16
General preparations	16
Before the installation of the wires	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	19
Passages	19
To make an island	19
To make a secondary area	20
To examine where to put the guide wire	21
Work area examples	21
Installation of the product	21
Installation tools	21
To install the charging station	22
To install the boundary wire	23
To install the guide wire	23
To put the wire into position with stakes	24
To bury the boundary wire or the guide wire	24
To extend the boundary wire or the guide wire	24
After the installation of the product	25
To do a visual check of the charging station	25
Automower® Connect	25
To install the Automower® Connect app	25
To pair Automower® Connect and the product	25
My mowers	25
Firmware over the air (FOTA)	25
To set the Firmware over the air (FOTA)	25
Automower® Direct	25
To start to use Automower® Direct	26
User interface overview	26
To start the product for the first time	26
Settings in Automower® Connect	27
Schedule	27
To edit the schedule settings	27
To add a new schedule setting	27
To calculate the schedule setting	27
Operation	27
Weather timer	27
To set the Weather timer	28
ECO mode	28
To set the ECO mode	28
Installation	28
To find the charging station	28
To change the signal range of the charging station	28
To set the delay time for the guide wire and the boundary wire	28
Lawn coverage	29
To set the GPS function	29
To set the Lawn Coverage function	29
To measure the distance from the charging station	29
To do a test of the Lawn Coverage function	29
Drive Past Wire	29
To set the Drive past wire	30
Starting point	30
To set the starting point	30
Accessories	30
To avoid collisions with the mower house	30
General (Bluetooth® only)	30
Time & date	30
To set the time & date	30
Reset to factory settings	30
To reset to factory settings	30
Security (Bluetooth® only)	30
New loop signal	30
To create a New loop signal	31
To change the PIN code	31
Theft protection	31
Alarm duration	31
STOP button pressed	31
Carried away	31
To set the Theft protection	31
GeoFence	31
To set the center position for the GeoFence function	31
Automower® Connect (Bluetooth® only)	31
Messages	31
Operation	32
To switch on the product	32
Operating modes	32
Main area	32
Secondary area (2nd area)	32
Park	32
Park until further notice	32
Park for a selected number of hours	33
To stop the product	33
To switch off the product	33
To charge the battery	33
To adjust the cutting height with Automower® Connect	33
Maintenance	35
Introduction - maintenance	35
Clean the product	35
To clean the blade disc	35
Chassis	36
Wheels	36
The body of the product	36
Charging station	36
Replace the blades	36
To replace the blades	36
To replace the top covers	37
To remove the front top cover	37
To install the front top cover	37
To remove the rear top cover	38
To install the rear top cover	39
Battery	39
Winter service	39
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	48
Indicator lamp in the charging station	49
Symptoms	50
Find breaks in the loop wire	51
Transportation, storage and disposal	54
Transportation	54
Storage	54
Disposal	54
To remove the battery	54
Technical data	56
Technical data	56
Registered trademarks	58
Warranty	59
Warranty terms	59
Applicable to US/CA market	60
Supplier's Declaration of Conformity	60

Match case Limit results 1 per page

3.10.5.1 To start to use Automower

Direct

Download the Automower

Connect app on

your mobile device.

Select Automower

Direct on the start

screen of the Automower

Connect app.

Start Bluetooth

on your mobile device and

on the product, refer to

To start the product

for the first time on page 26

Go to the

Settings

symbol in the display and

activate Bluetooth

Select the product to pair with in the

Automower

Connect app.

Enter the PIN code for the product.

Note:

You have access to the menus and

functions as long as you are in Bluetooth

short-

range.

3.10.6 User interface overview

The user interface overview below shows examples of Automower

Connect.

Automower

Connect

ERROR

Charging station Blocked

MORE DETAILS

Schedule

Map

My Automower

MOWING

Mowing session ends 13:30

PARK

PAUSE

Schedule

Map

My Automower

PARKED

Next start tomorrow 16:30

PARK

START

Schedule

Map

My Automower

PAUSED

PARK

START

Schedule

Map

My Automower

3.11 To start the product for the first

time

When the product is switched on for the first time,

there are some basic settings to do before the

product can start to operate.

Push the

ON/OFF

button for 3 seconds to

switch on the product.

Note:

The Bluetooth

pairing mode is on for

3 minutes and the LED light is flashing blue.

If the product does not pair with Bluetooth

in 3 minutes, switch off the product. Wait

until the LED status indicator is not lit, and

then switch on the product again.

Enter the factory PIN code.

Log on to your Husqvarna account in the

Automower

Connect app to pair your

product with Automower

Connect.

Note:

It is recommended to pair your product

with Automower

Connect to get access to

all functions in the product. If it is not

necessary to pair your product with

Automower

Connect, push the

arrow

symbol to continue to the menu.

Start Bluetooth

on your mobile device.

Select

My mowers

in the Automower

Connect app, and then select the plus sign

(+).

Select model. The Automower

Connect

app searches for available products within

short-range (Bluetooth

- Installation

1427 - 002 - 20.12.2019