Husqvarna AUTOMOWER 535 AWD Owner Manual - Page 52

Indicator lamp, in the charging station on Guide

Get Husqvarna AUTOMOWER 535 AWD PDF manuals and user guides View all Husqvarna AUTOMOWER 535 AWD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

in the boundary loop. Refer to Indicator lamp in the charging station on page 49. 2. Check that the boundary wire connections to the charging station are properly connected and not damaged. Check that the indicator lamp in the charging station is still flashing blue. AR POWER AL G1 3. Switch the connections between the guide wire and the boundary wire in the charging station. Start by switching connection AL and G1. Some models have additional guide wires (G2, G3). The same procedure can be followed for them. If the indicator lamp is lit with a solid green light, then the break is somewhere on the boundary wire between AL and the point where the guide wire is connected to the boundary wire (thick black line in the illustration). AL G1 Guide To rectify the fault you will need boundary wire, connector(s) and coupler(s): a) If the suspected boundary wire is short then it is easiest to exchange all of the boundary wire between AL and the point where the guide wire is connected to the boundary wire (thick black line). b) If the suspected boundary wire is long (thick black line) then do as follows: Put AL and G1 back to their original positions. Then disconnect AR. Connect a new loop wire to AR. Connect the other end of this new loop wire at the middle of the suspected wire section. 52 - Troubleshooting 1427 - 002 - 20.12.2019

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
in the boundary loop. Refer to
Indicator lamp
in the charging station on page 49
.
2.
Check that the boundary wire connections to
the charging station are properly connected
and not damaged. Check that the indicator
lamp in the charging station is still flashing
blue.
AR
AL
G1
POWER
3.
Switch the connections between the guide
wire and the boundary wire in the charging
station.
Start by switching connection AL and G1.
Some models have additional guide wires
(G2, G3). The same procedure can be
followed for them.
If the indicator lamp is lit with a solid green
light, then the break is somewhere on the
boundary wire between AL and the point
where the guide wire is connected to the
boundary wire (thick black line in the
illustration).
Guide
G1
AL
To rectify the fault you will need boundary
wire, connector(s) and coupler(s):
a) If the suspected boundary wire is short
then it is easiest to exchange all of the
boundary wire between AL and the point
where the guide wire is connected to the
boundary wire (thick black line).
b) If the suspected boundary wire is long
(thick black line) then do as follows: Put AL
and G1 back to their original positions. Then
disconnect AR. Connect a new loop wire to
AR. Connect the other end of this new loop
wire at the middle of the suspected wire
section.
52
- Troubleshooting
1427 - 002 - 20.12.2019