Husqvarna XciteZ380 Owner Manual - Page 25

To install the pump belt, To do a check of the engine oil level, To replace the engine oil

Get Husqvarna XciteZ380 PDF manuals and user guides View all Husqvarna XciteZ380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

1. Lift the rear of the product and put supports below it. 2. Remove the drive wheels. 3. Remove the deck belt. Refer to To remove the deck belt on page 24. 4. Remove the clutch stop to get access to the pump belt. 5. Loosen the nuts on the eye bolt to decrease the tension in the pump belt. 6. The oil level must be between the marks on the dipstick. If the level is near the ADD mark, fill oil to the FULL mark. 6. Remove the pump belt from the engine and the pump pulleys. To install the pump belt 1. Loosen the nuts on the eye bolt to decrease the tension in the pump belt. 2. Put the pump belt around the right and left pump pulleys. 3. Put the pump belt around the engine pulley. 4. Install the clutch stop. 5. Turn the nut on the eye bolt on the idler pulley to adjust the tension of the pump belt. The length of the spring must be 1.38-1.50 in. 6. Install the deck belt. Refer to To install the deck belt on page 24. 7. Install the drive wheels. 8. Remove the supports and lower the rear of the product. To do a check of the engine oil level 1. Park the product on level ground and stop the engine. 2. Loosen the dipstick and pull it out. 3. Clean the oil from the dipstick. 4. Put the dipstick in the hole for the dipstick and tighten it. 5. Loosen and pull the dipstick out and read the oil level. 7. Fill the oil through the hole for the dipstick. Fill the oil slowly. Note: Refer to Technical data on page 31 for the types of engine oil that Husqvarna recommends. Do not mix different types of oil. 8. Tighten the dipstick fully before you start the engine. To replace the engine oil If the engine is cold, start the engine for 1-2 minutes before you drain the engine oil. This makes the engine oil warm and faster to drain. WARNING: Do not operate the engine for more than 1-2 minutes before you drain the engine oil. The engine oil becomes very hot and can cause burn injuries. Let the engine become cool before you drain the engine oil. WARNING: If you spill engine oil on your body, clean with soap and water. 1. Park the product on level ground and stop the engine. 2. Engage the parking brake. Refer to To engage and disengage the parking brake on page 15. 3. Remove all dirt around the oil tank cap. 4. Remove the oil tank cap and the dipstick. 5. Find the oil drain plug on the engine. Refer to Product overview on page 3. 6. Put a container below the oil drain plug. 7. Remove the oil drain plug. 8. Let the oil run out into the container. 9. Replace and install the oil drain plug. 10. Fill with new oil and do a check of the engine oil level. Refer to To do a check of the engine oil level on page 25. 11. Install the oil tank cap and the dipstick. Note: For safe disposal of used engine oil, refer to Disposal on page 30. 1922 - 002 - 03.11.2022 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
1.
Lift the rear of the product and put supports
below it.
2.
Remove the drive wheels.
3.
Remove the deck belt. Refer to
To remove the
deck belt on page 24
.
4.
Remove the clutch stop to get access to the
pump belt.
5.
Loosen the nuts on the eye bolt to decrease the
tension in the pump belt.
6.
Remove the pump belt from the engine and the
pump pulleys.
To install the pump belt
1.
Loosen the nuts on the eye bolt to decrease the
tension in the pump belt.
2.
Put the pump belt around the right and left pump
pulleys.
3.
Put the pump belt around the engine pulley.
4.
Install the clutch stop.
5.
Turn the nut on the eye bolt on the idler pulley to
adjust the tension of the pump belt. The length of
the spring must be 1.38–1.50 in.
6.
Install the deck belt. Refer to
To install the deck
belt on page 24
.
7.
Install the drive wheels.
8.
Remove the supports and lower the rear of the
product.
To do a check of the engine oil level
1.
Park the product on level ground and stop the
engine.
2.
Loosen the dipstick and pull it out.
3.
Clean the oil from the dipstick.
4.
Put the dipstick in the hole for the dipstick and
tighten it.
5.
Loosen and pull the dipstick out and read the oil
level.
6.
The oil level must be between the marks on the
dipstick. If the level is near the ADD mark, fill oil
to the FULL mark.
7.
Fill the oil through the hole for the dipstick. Fill
the oil slowly.
Note:
Refer to
Technical data on page 31
for the types of engine oil that Husqvarna
recommends. Do not mix different types of oil.
8.
Tighten the dipstick fully before you start the
engine.
To replace the engine oil
If the engine is cold, start the engine for 1–2 minutes
before you drain the engine oil. This makes the
engine oil warm and faster to drain.
WARNING:
Do not operate the
engine for more than 1–2 minutes before
you drain the engine oil. The engine oil
becomes very hot and can cause burn
injuries. Let the engine become cool
before you drain the engine oil.
WARNING:
If you spill engine oil on
your body, clean with soap and water.
1.
Park the product on level ground and stop the
engine.
2.
Engage the parking brake. Refer to
To engage
and disengage the parking brake on page 15
.
3.
Remove all dirt around the oil tank cap.
4.
Remove the oil tank cap and the dipstick.
5.
Find the oil drain plug on the engine. Refer to
Product overview on page 3
.
6.
Put a container below the oil drain plug.
7.
Remove the oil drain plug.
8.
Let the oil run out into the container.
9.
Replace and install the oil drain plug.
10. Fill with new oil and do a check of the engine oil
level. Refer to
To do a check of the engine oil
level on page 25
.
11. Install the oil tank cap and the dipstick.
Note:
For safe disposal of used engine oil, refer to
Disposal on page 30
.
1922 - 002 - 03.11.2022
25