IBM HS20 Hardware Maintenance Manual - Page 46

Replacing the blade server bezel assembly, Review Appendix B, Safety information

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

3. Lower the cover so that the slots at the rear slide down onto the pins at the rear of the blade server, as shown in Figure 15 on page 35. Before closing the cover, make sure that all components are installed and seated correctly and that you have not left loose tools or parts inside the blade server. 4. Pivot the cover to the closed position as shown in Figure 15 on page 35, until it clicks into place. Replacing the blade server bezel assembly This section contains information on how to remove and install the blade server bezel assembly. Removing the blade server bezel assembly To install certain options you must first remove the blade server bezel assembly. Figure 16 shows how to remove the bezel assembly from a blade server. Note: The illustrations in this document might differ slightly from your hardware. Bezel-assembly release Bezel-assembly release Control panel connector Control-panel cable Figure 16. Blade server bezel placement Complete the following steps to remove the blade server bezel assembly: 1. Review Appendix B, "Safety information," on page 97 and "Installation guidelines" on page 27. 2. Open the blade server cover. 3. Press the bezel-assembly release and pull the bezel assembly away from the blade server approximately 1.2 cm (0.5 inch). 4. Disconnect the control-panel cable from the control-panel connector. 5. Pull the bezel assembly away from the blade server. 6. Store the bezel assembly in a safe place. 36 BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
3.
Lower the cover so that the slots at the rear slide down onto the pins at the rear
of the blade server, as shown in Figure 15 on page 35. Before closing the cover,
make sure that all components are installed and seated correctly and that you
have not left loose tools or parts inside the blade server.
4.
Pivot the cover to the closed position as shown in Figure 15 on page 35, until it
clicks into place.
Replacing the blade server bezel assembly
This section contains information on how to remove and install the blade server
bezel assembly.
Removing the blade server bezel assembly
To install certain options you must first remove the blade server bezel assembly.
Figure 16 shows how to remove the bezel assembly from a blade server.
Note:
The illustrations in this document might differ slightly from your hardware.
Complete the following steps to remove the blade server bezel assembly:
1.
Review Appendix B, “Safety information,” on page 97 and “Installation
guidelines” on page 27.
2.
Open the blade server cover.
3.
Press the bezel-assembly release and pull the bezel assembly away from the
blade server approximately 1.2 cm (0.5 inch).
4.
Disconnect the control-panel cable from the control-panel connector.
5.
Pull the bezel assembly away from the blade server.
6.
Store the bezel assembly in a safe place.
Control panel
connector
Bezel-assembly
release
Bezel-assembly
release
Control-panel
cable
Figure 16. Blade server bezel placement
36
BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide