IBM HS20 Hardware Maintenance Manual - Page 52

Review Appendix B, Safety information, on and Installation - chassis

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Alignment marks Heat sink Microprocessor Heat sink filler Microprocessor locking lever Figure 20. Installing a second microprocessor Complete the following steps to install an additional microprocessor: 1. Review Appendix B, "Safety information," on page 97 and "Installation guidelines" on page 27. 2. Shut down the operating system, turn off the blade server, and remove the blade server from the BladeCenter unit (see "Removing the blade server from the BladeCenter unit" on page 29). 3. Carefully lay the blade server on a flat, static-protective surface. 4. Open the blade server cover (see "Opening the blade server cover" on page 34). 5. Remove the bezel assembly (see "Removing the blade server bezel assembly" on page 36). 6. Locate microprocessor socket 2 on the system board (see Figure 29 on page 60). 7. Remove the heat-sink filler. 8. Install the microprocessor: a. Remove the protective cover, tape, or label from the surface of the microprocessor socket, if one is present. b. Touch the static-protective package containing the new microprocessor to any unpainted metal surface on the BladeCenter chassis or any unpainted surface on any other grounded rack component for at least two seconds; then, remove the microprocessor from the package. Attention: Do not use any tools or sharp objects to lift the locking lever on the microprocessor socket. Doing so might result in permanent damage to the system board. c. Rotate the locking lever on the microprocessor socket from its closed and locked position (Figure 21 on page 43) until it stops or clicks in the fully open position (approximately a 135° angle), as shown in Figure 22 on page 43. Attention: You must ensure that the locking lever on the microprocessor socket is in the fully open position before you insert the microprocessor in the socket. Failure to do so might result in permanent damage to the microprocessor, microprocessor socket, and system board. 42 BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Complete the following steps to install an additional microprocessor:
1.
Review Appendix B, “Safety information,” on page 97 and “Installation
guidelines” on page 27.
2.
Shut down the operating system, turn off the blade server, and remove the
blade server from the BladeCenter unit (see “Removing the blade server from
the BladeCenter unit” on page 29).
3.
Carefully lay the blade server on a flat, static-protective surface.
4.
Open the blade server cover (see “Opening the blade server cover” on page
34).
5.
Remove the bezel assembly (see “Removing the blade server bezel assembly”
on page 36).
6.
Locate microprocessor socket 2 on the system board (see Figure 29 on page
60).
7.
Remove the heat-sink filler.
8.
Install the microprocessor:
a.
Remove the protective cover, tape, or label from the surface of the
microprocessor socket, if one is present.
b.
Touch the static-protective package containing the new microprocessor to
any
unpainted
metal surface on the BladeCenter chassis or any
unpainted
surface on any other grounded rack component for at least two seconds;
then, remove the microprocessor from the package.
Attention:
Do not use any tools or sharp objects to lift the locking lever
on the microprocessor socket. Doing so might result in permanent damage
to the system board.
c.
Rotate the locking lever on the microprocessor socket from its closed and
locked position (Figure 21 on page 43) until it stops or clicks in the fully
open position (approximately a 135° angle), as shown in Figure 22 on page
43.
Attention:
You must ensure that the locking lever on the microprocessor
socket is in the fully open position before you insert the microprocessor in
the socket. Failure to do so might result in permanent damage to the
microprocessor, microprocessor socket, and system board.
Heat sink
Microprocessor
Microprocessor
locking lever
Heat sink filler
Alignment marks
Figure 20. Installing a second microprocessor
42
BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide