IBM HS20 Hardware Maintenance Manual - Page 83

Run the Configuration/Setup Utility program, Disconnect the external cable on the serial port.

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Note: See "System" on page 94 to determine which components should be replaced by a field service technician. Error code/symptom FRU/action 762 (Coprocessor configuration error) 1. Run the Configuration/Setup Utility program. 2. Battery. 3. Microprocessor. 962 (Parallel port configuration error) 1. Run the Configuration/Setup Utility program and verify that the parallel-port setting is correct. 2. System board. 11XX (System board serial port 1 or 2 error) 1. Disconnect the external cable on the serial port. 2. Run the Configuration/Setup Utility program. 3. System board. 1162 (Serial port configuration conflicts) 1. Run the Configuration/Setup Utility program and ensure that the IRQ and I/O port assignments needed by the serial port are available. 2. If all interrupts are being used by adapters, remove an adapter or force other adapters to share an interrupt. 1301 (I2C cable to operator information panel not found) 1. Cable 2. Operator information card 3. Power switch assembly 4. System board 1302 1. Cable (I2C cable from system board to power-on and reset switches not found) 2. Power switch assembly 3. System board 1303 (I2C cable from system board to power backplane not found) 1. Cable 2. Power supply 3. System board 1304 (I2C cable to diagnostic LED board not found) 1. Power switch assembly 2. System board 1762 (Hard disk configuration error) 1. Hard disk drive. 2. Hard disk drive cables. 3. Run the Configuration/Setup Utility program. 4. SCSI storage expansion unit. 5. System board. 178X (Fixed disk error) 1. Hard disk drive cables. 2. Run diagnostics. 3. Hard disk drive. 4. System board. 1800 (No more hardware interrupt available for PCI adapter) 1. Run Configuration/Setup to verify that the interrupt resource settings are correct. 2. Failing adapter (if installed). 3. System board. Chapter 8. Symptom-to-FRU index 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Note:
See “System” on page 94 to determine which components should be replaced by a field service technician.
Error code/symptom
FRU/action
762
(Coprocessor configuration error)
1.
Run the Configuration/Setup Utility program.
2.
Battery.
3.
Microprocessor.
962
(Parallel port configuration error)
1.
Run the Configuration/Setup Utility program and verify that the
parallel-port setting is correct.
2.
System board.
11XX
(System board serial port 1 or 2 error)
1.
Disconnect the external cable on the serial port.
2.
Run the Configuration/Setup Utility program.
3.
System board.
1162
(Serial port configuration conflicts)
1.
Run the Configuration/Setup Utility program
and ensure that the
IRQ and I/O port assignments needed by the serial port are
available.
2.
If all interrupts are being used by adapters, remove an adapter or
force other adapters to share an interrupt.
1301
(I2C cable to operator information panel
not found)
1.
Cable
2.
Operator information card
3.
Power switch assembly
4.
System board
1302
(I2C cable from system board to power-on
and reset switches not found)
1.
Cable
2.
Power switch assembly
3.
System board
1303
(I2C cable from system board to power
backplane not found)
1.
Cable
2.
Power supply
3.
System board
1304
(I2C cable to diagnostic LED board not
found)
1.
Power switch assembly
2.
System board
1762
(Hard disk configuration error)
1.
Hard disk drive.
2.
Hard disk drive cables.
3.
Run the Configuration/Setup Utility program.
4.
SCSI storage expansion unit.
5.
System board.
178X
(Fixed disk error)
1.
Hard disk drive cables.
2.
Run diagnostics.
3.
Hard disk drive.
4.
System board.
1800
(No more hardware interrupt available for
PCI adapter)
1.
Run Configuration/Setup to verify that the interrupt resource
settings are correct.
2.
Failing adapter (if installed).
3.
System board.
Chapter 8. Symptom-to-FRU index
73