IBM HS20 Hardware Maintenance Manual - Page 62

Completing the installation

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

a. Use your finger to press down on one side of the battery; then, slide the battery out from its socket. The spring mechanism will push the battery out toward you as you slide it from the socket. Note: You might need to lift the battery clip slightly with your fingernail to make it easier to slide the battery. b. Use your thumb and index finger to pull the battery from under the battery clip. Note: After you remove the battery, ensure that the battery clip is touching the base of the battery socket by pressing gently on the clip. 7. Insert the new battery: a. Tilt the battery so that you can insert it into the socket, under the battery clip. b. As you slide it under the battery clip, press the battery down into the socket. 8. Close the blade server cover (see "Closing the blade server cover" on page 35). Statement 21 CAUTION: Hazardous energy is present when the blade server is connected to the power source. Always replace the blade cover before installing the blade server. 9. Reinsert the blade server into the bay in the BladeCenter unit. 10. Turn on the blade server. 11. Start the blade server Configuration/Setup Utility program and set configuration parameters as needed (see "Using the Configuration/Setup Utility program" on page 14). Completing the installation To complete the installation, perform the following tasks. 1. Reinstall the blade server bezel assembly, if you removed it (see "Installing the blade server bezel assembly" on page 37). 2. Close the blade server cover, unless you installed the expansion unit option (see "Closing the blade server cover" on page 35). 52 BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
a.
Use your finger to press down on one side of the battery; then, slide the
battery out from its socket. The spring mechanism will push the battery out
toward you as you slide it from the socket.
Note:
You might need to lift the battery clip slightly with your fingernail to
make it easier to slide the battery.
b.
Use your thumb and index finger to pull the battery from under the battery
clip.
Note:
After you remove the battery, ensure that the battery clip is touching
the base of the battery socket by pressing gently on the clip.
7.
Insert the new battery:
a.
Tilt the battery so that you can insert it into the socket, under the battery
clip.
b.
As you slide it under the battery clip, press the battery down into the
socket.
8.
Close the blade server cover (see “Closing the blade server cover” on page
35).
Statement 21
CAUTION:
Hazardous energy is present when the blade server is connected to the power source.
Always replace the blade cover before installing the blade server.
9.
Reinsert the blade server into the bay in the BladeCenter unit.
10.
Turn on the blade server.
11.
Start the blade server Configuration/Setup Utility program and set configuration
parameters as needed (see “Using the Configuration/Setup Utility program” on
page 14).
Completing the installation
To complete the installation, perform the following tasks.
1.
Reinstall the blade server bezel assembly, if you removed it (see “Installing the
blade server bezel assembly” on page 37).
2.
Close the blade server cover, unless you installed the expansion unit option
(see “Closing the blade server cover” on page 35).
52
BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide