IBM HS20 Hardware Maintenance Manual - Page 47

Installing the blade server bezel assembly, Installing IDE disk drives - install windows 2000

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installing the blade server bezel assembly Figure 17 shows how to install the bezel assembly on the blade server. Note: The illustrations in this document might differ slightly from your hardware. Bezel-assembly release Bezel-assembly release Control panel connector Control-panel cable Figure 17. Blade server bezel placement Complete the following steps to install the blade server bezel assembly: 1. Read the safety information beginning at Appendix B, "Safety information," on page 97 and "Installation guidelines" on page 27. 2. Connect the control-panel cable to the control-panel connector on the system board (see Figure 29 on page 60). 3. Carefully slide the bezel assembly onto the blade server as shown in Figure 17, until it clicks into place. Installing IDE disk drives The blade server has two connectors on the system board for installing an optional 2.5-inch HS20 IDE hard disk drive or BladeCenter flash disk drive. Note: In this document, both types of drives are referred to as IDE drives. Each IDE connector is on a separate bus. Some models come with at least one IDE hard disk drive already installed. By installing a second IDE hard disk drive, you can implement and manage RAID level-1 under both the Linux and Microsoft Windows 2000 operating systems. Attention: To maintain proper system cooling, do not operate the BladeCenter unit without either a blade server, expansion unit, or filler blade installed in each blade bay for more than one minute for the BladeCenter unit and 20 minutes for the BladeCenter T unit. Note: The illustrations in this document might differ slightly from your hardware. Chapter 5. Customer replacement units 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Installing the blade server bezel assembly
Figure 17 shows how to install the bezel assembly on the blade server.
Note:
The illustrations in this document might differ slightly from your hardware.
Complete the following steps to install the blade server bezel assembly:
1.
Read the safety information beginning at Appendix B, “Safety information,” on
page 97 and “Installation guidelines” on page 27.
2.
Connect the control-panel cable to the control-panel connector on the system
board (see Figure 29 on page 60).
3.
Carefully slide the bezel assembly onto the blade server as shown in Figure 17,
until it clicks into place.
Installing IDE disk drives
The blade server has two connectors on the system board for installing an optional
2.5-inch HS20 IDE hard disk drive or BladeCenter flash disk drive.
Note:
In this document, both types of drives are referred to as IDE drives.
Each IDE connector is on a separate bus. Some models come with at least one
IDE hard disk drive already installed. By installing a second IDE hard disk drive,
you can implement and manage RAID level-1 under both the Linux and Microsoft
Windows 2000 operating systems.
Attention:
To maintain proper system cooling, do not operate the BladeCenter
unit without either a blade server, expansion unit, or filler blade installed in each
blade bay for more than one minute for the BladeCenter unit and 20 minutes for the
BladeCenter T unit.
Note:
The illustrations in this document might differ slightly from your hardware.
Control panel
connector
Bezel-assembly
release
Bezel-assembly
release
Control-panel
cable
Figure 17. Blade server bezel placement
Chapter 5. Customer replacement units
37