IBM HS20 Hardware Maintenance Manual - Page 78

No-beep symptoms, Diagnostic error codes, Run Diagnostics.

Get IBM HS20 - BladeCenter - 8832 PDF manuals and user guides
UPC - 087944983033
View all IBM HS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Note: See "System" on page 94 to determine which components should be replaced by a field service technician. Beep/symptom FRU/action Two short beeps (Information only, the configuration has changed) 1. Run Diagnostics. 2. Run the Configuration/Setup Utility program. Three short beeps 1. DIMM 2. System board One continuous beep 1. Microprocessor 2. Optional microprocessor (if installed) 3. System board Repeating short beeps 1. Keyboard 2. System board No-beep symptoms Note: See "System" on page 94 to determine which components should be replaced by a field service technician. No-beep symptom FRU/action No beep and the system operates correctly. v System board No beep and no video (System v See "Undetermined problems" on page 90. error LED is OFF) No beep and no video (System v See "Light path diagnostics" on page 24. Attention LED is ON) Diagnostic error codes Note: In the following error codes, if XXX is 000, 195, or 197, do not replace a FRU. The description for these error codes are: 000 The test passed. 195 The Esc key was pressed to stop the test. 197 Warning; a hardware failure might not have occurred. For all error codes, replace the FRU or take the action indicated. Note: See "System" on page 94 to determine which components should be replaced by a field service technician. Error code/symptom FRU/action 001-250-000 (Failed system board ECC) v System board 001-250-001 (Failed processor board ECC) v System board 001-292-000 (Core system: failed/CMOS checksum failed) v Load BIOS defaults and rerun test. 001-XXX-000 (Failed core tests) v System board 001-XXX-001 (Failed core tests) v System board 68 BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Note:
See “System” on page 94 to determine which components should be replaced by a field service technician.
Beep/symptom
FRU/action
Two short beeps
(Information only, the configuration
has changed)
1.
Run Diagnostics.
2.
Run the Configuration/Setup Utility program.
Three short beeps
1.
DIMM
2.
System board
One continuous beep
1.
Microprocessor
2.
Optional microprocessor (if installed)
3.
System board
Repeating short beeps
1.
Keyboard
2.
System board
No-beep symptoms
Note:
See “System” on page 94 to determine which components should be replaced by a field service technician.
No-beep symptom
FRU/action
No beep and the system
operates correctly.
v
System board
No beep and no video
(System
error LED is OFF)
v
See “Undetermined problems” on page 90.
No beep and no video
(System
Attention LED is ON)
v
See “Light path diagnostics” on page 24.
Diagnostic error codes
Note:
In the following error codes, if
XXX
is
000
,
195
, or
197
,
do not
replace a
FRU. The description for these error codes are:
000
The test passed.
195
The Esc key was pressed to stop the test.
197
Warning; a hardware failure might not have occurred.
For all error codes, replace the FRU or take the action indicated.
Note:
See “System” on page 94 to determine which components should be replaced by a field service technician.
Error code/symptom
FRU/action
001-250-000
(Failed system board ECC)
v
System board
001-250-001
(Failed processor board ECC)
v
System board
001-292-000
(Core system: failed/CMOS
checksum failed)
v
Load BIOS defaults and rerun test.
001-XXX-000
(Failed core tests)
v
System board
001-XXX-001
(Failed core tests)
v
System board
68
BladeCenter HS20 Type 8832: Hardware Maintenance Manual and Troubleshooting Guide