IBM HS40 User Guide - Page 39

Installing, drive - hs20

Get IBM HS40 - BladeCenter - 8839 PDF manuals and user guides
UPC - 000435160188
View all IBM HS40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

3. Press the bezel-assembly release and rotate the bezel assembly away from the blade server chassis; then, unhook the tabs on the bottom of the bezel from the holes on the server chassis and remove the bezel. Bezel-assembly release Bezel-assembly release 4. Disconnect the control-panel cable from the control-panel connector. Control-panel connector Control-panel cable 5. Pull the bezel assembly away from the blade server. 6. Store the bezel assembly in a safe place. Installing an IDE drive Your blade server has two connectors on the I/O board for installing an optional 2.5-inch HS20 IDE Hard Disk Drive or BladeCenter Flash Disk Drive. Each IDE connector is on a separate bus. Some models might come with at least one hard disk drive or one flash drive already installed. Note: In this document, both types of drives are referred to as IDE drives. Each IDE connector is on a separate bus. Depending on your blade server, at least one IDE hard disk drive might already be installed. If your blade server is equipped with one IDE hard disk drive, you can install an additional IDE hard disk drive. These two IDE hard disk drives can be used to implement and manage redundant Chapter 3. Installing options 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
3.
Press
the
bezel-assembly
release
and
rotate
the
bezel
assembly
away
from
the
blade
server
chassis;
then,
unhook
the
tabs
on
the
bottom
of
the
bezel
from
the
holes
on
the
server
chassis
and
remove
the
bezel.
Bezel-assembly release
Bezel-assembly release
4.
Disconnect
the
control-panel
cable
from
the
control-panel
connector.
Control-panel
cable
Control-panel
connector
5.
Pull
the
bezel
assembly
away
from
the
blade
server.
6.
Store
the
bezel
assembly
in
a
safe
place.
Installing
an
IDE
drive
Your
blade
server
has
two
connectors
on
the
I/O
board
for
installing
an
optional
2.5-inch
HS20
IDE
Hard
Disk
Drive
or
BladeCenter
Flash
Disk
Drive.
Each
IDE
connector
is
on
a
separate
bus.
Some
models
might
come
with
at
least
one
hard
disk
drive
or
one
flash
drive
already
installed.
Note:
In
this
document,
both
types
of
drives
are
referred
to
as
IDE
drives.
Each
IDE
connector
is
on
a
separate
bus.
Depending
on
your
blade
server,
at
least
one
IDE
hard
disk
drive
might
already
be
installed.
If
your
blade
server
is
equipped
with
one
IDE
hard
disk
drive,
you
can
install
an
additional
IDE
hard
disk
drive.
These
two
IDE
hard
disk
drives
can
be
used
to
implement
and
manage
redundant
Chapter
3.
Installing
options
25