JVC GY-DV700WUCL Instruction Manual - Page 14

2. CONTROLS, INDICATORS AND CONNECTORS 2-2 Right Side Section (Cont'd) [Audio Setting Section] FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK BACK L NORMAL SPOT L STRETCH NORMAL COMPRESS LOLUX PRST A B ON KNEE OFF AUTO BARS CAM HML SAVE STBY VTR GAIN OUTPUT WHT.BAL NG POWER ON OFF OPERATE/WARNING RESET MONITOR SELECT CH-1 AUDIO CH-2 LEVEL LIGHT ON OFF COUNTER CTL TC UB q we 1 Monitoring loudspeaker • Enables EE monitoring of the input audio signal during recording, in the record-pause mode or in the stop mode. Outputs the playback sound in the playback mode. The sound to be output can be selected using the MONITOR SELECT switch 4. • The loudspeaker volume can be adjusted with the MONITOR volume control 2 on page 12. The audio from the loudspeaker is not output when an earphone is plugged into the EARPHONE jack 2 on page 20. The warning alarm tones are also output through this loudspeaker.  See "ALARM INDICATIONS" on pages 86. 2 [CH1 AUDIO LEVEL] CH1 audio input level control Adjust the audio input level of the CH1 audio channel with this control. • To use this control, set the CH1 AUDIO SELECT switch 5 to "MANUAL". This control works regardless of the setting of the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE. To use this control, set the AUDIO LEVEL CH-1 audio input level control (7 on page 10) on the front section to the maximum (10) position, or set the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE to "DISABLE". 3 [CH2 AUDIO LEVEL] CH2 audio input level control Adjust the audio input level of the CH2 audio channel with this control. • This control is valid only when the CH2 AUDIO SELECT switch 6 is set to "MANUAL". 4 [MONITOR SELECT] audio monitor selector switch This switch is used to select the monitor sound output from the monitoring loudspeaker 1 or via the EARPHONE jack 2 on page 20. CH-1 : The CH1 channel audio is output. MIX : CH1 and CH2 channel audio are output mixed. CH-2 : The CH2 channel audio is output. CAUTION: Make sure to move switches all the way. Do not leave a switch stopped in a midway position. Noise will be generated and operation irregularities will occur. r ty CH-1 AUDIO CH-2 LEVEL AUTO MANUAL AUDIO SELECT AUDIO INPUT CH-1 CH-2 FRONT REAR ui 5 [CH-1 AUDIO SELECT] selector switch This switch is used to select the method for adjusting the audio input level of the CH-1 audio channel. AUTO : The audio input level is held at the reference level even when sounds greater than the reference level are input. The audio input level does not increase when the input level is low. MANUAL: The audio input level can be adjusted with the CH-1 AUDIO LEVEL control 2 or the CH-1 AUDIO LEVEL control 7 on page 10. To use the AUDIO LEVEL CH-1 audio input level control on the front section, set the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE to "ENABLE". 6 [CH-2 AUDIO SELECT] selector switch This switch is used to select the method for adjusting the audio input level of the CH-2 audio channel. AUTO : The audio input level is held at the reference level even when sounds greater than the reference level are input. The audio input level does not increase when the input level is low. MANUAL: The audio input level can be adjusted with the CH-2 AUDIO LEVEL control 3. 7 [CH-1 AUDIO INPUT] selector switch This switch is used to select the input section of the CH1 audio channel. FRONT : The sound from the MIC IN connector on the front side section is input. REAR : The sound from the CH-1 AUDIO IN connector on the rear side section is input. 8 [CH-2 AUDIO INPUT] selector switch This switch is used to select the input section of the CH2 audio channel. FRONT : The sound from the MIC IN connector on the front side section is input. REAR : The sound from the CH-2 AUDIO IN connector on the rear side section is input. 14