JVC GY-DV700WUCL Instruction Manual - Page 48
Audio Input Level Adustment, Manual Adjustment of Audio Input Level
View all JVC GY-DV700WUCL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 48 highlights
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING 6-9 Audio Input Level Adjustment VF OFF ZEBRA SKIN ON AREA AUTO WHITE ACCU FOCUS VTR AUDIO LEVEL CH-1 TAKE FUJINON ASPHERIC & IF 19x TV . ZOOM 5 7 10 15 30 ∞ ft 1.5 2 3 5 10 m 8.7 20 C 16 11 8 5.6 M O FILTER 1 3200k 2 5600k+1/8ND 3 5600k 4 5600k+1/64ND SHUTTER STATUS A CR MENU ALARM MONITOR AUTO IRIS FULL AUTO BLACK BACK L NORMAL SPOT L STRETCH NORMAL COMPRESS LOLUX PRST A B ON KNEE OFF AUTO BARS CAM HML SAVE STBY VTR GAIN OUTPUT WHT.BAL NG POWER ON OFF OPERATE/WARNING RESET MONITOR SELECT CH-1 AUDIO CH-2 LEVEL LIGHT ON OFF COUNTER CTL TC UB CH-1 Audio select switch CH-2 Audio select switch CH-1 AUDIO CH-2 LEVEL AUTO MANUAL AUDIO SELECT AUDIO INPUT CH-1 CH-2 FRONT REAR CH-1 audio input level control CH-1 audio input level control CH-2 audio input level control For each audio channel, use the AUDIO SELECT switches to select whether the audio input level adjustment should be set to AUTO mode or MANUAL mode. • When set to AUTO: Audio input level is fixed. In this mode, the audio input level control does not function. • When set to MANUAL: Audio input level can be adjusted using the audio input level controls for each audio input. Ⅲ Adjusting the audio input level control of the front section The audio input level control on the front section only affects the CH-1 channel sound. To use the audio input level control on the front section, make the following settings. • Set the CH-1 AUDIO SELECT switch to MANUAL. • Set the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE to "ENABLE". CAUTION: The audio input level controls on the side section work regardless of the setting of the VCR Setup Menu item No. 246 FRONT VOLUME ENABLE. Manual Adjustment of Audio Input Level The audio input level can be adjusted manually when the GYDV700W is in the record, record-pause or stop mode. 1. Set the AUDIO SELECT switch of the channel whose audio input level that you want to adjust manually to MANUAL. 2. Rotate the audio input level control corresponding to the audio input to be adjusted. • Adjust so that the peak level does not exceed the -3dB point when a loud sound is input. • With microphone input, since the limiter circuit is activated, the audio input level will not exceed 0 dB even if the recording level control is turned up. Ⅲ How to use the audio input level control on the front section 1 Set the audio input level control on the front section to maximum (10) position. 2 Initially, adjust the input level using the CH1 audio input level control on the side. 3 When a loud sound is input during recording, use the audio input level control on the front section to lower the input level. Level meter CH 1 CH 2 40 30 20 10 OVER AUTO OFF DEW 0 dB OVER SERVO RF L i 32k 48k AUD LOCK SP MENU WIDE REMAIN SLAVE PB NDF HOLD H M S F REV FWD E BATT F H M Viewfinder Status 1 Mode ACCU - FOCUS G F F5 . 6 STBY CH1 CH2 < 60 I SD B M 09 9 1 2 . 4V Audio leve Indicator level (reference) -38 -32 -26 -20 -14 -8 -2dB CAUTION: When the AUDIO INPUT LINE/MIC switch on the rear section is set to MIC, be sure to check that the microphone is connected to the AUDIO INPUT connector. If the microphone is not connected, increasing the audio input level could cause noise from the input connector to be recorded on the tape. When the microphone is not connected to the AUDIO INPUT connector on the rear panel, set the LINE/MIC switch to LINE or turn down the audio input level control. 48