JVC GY-DV700WUCL Instruction Manual - Page 68
VCR SETUP MENU CONTENTS, SERVO, SYSTEM, VIDEO, AUDIO, Group, Setting, Contents, Factory, Value
View all JVC GY-DV700WUCL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 68 highlights
12. SETUP MENU 12-1 VCR Setup Menu (Cont'd) VCR SETUP MENU CONTENTS Group SERVO /SYSTEM VIDEO AUDIO 68 Item Setting Value Upper row: Viewfinder display Lower row: Counter display indication Contents Factory Setting 050: REMOTE SELECT LOCAL Selection of the method for remote control of the VCR. LOCAL IEEE1394 LOCAL : Choose this setting when the VCR should RS232C be controlled using the operation buttons on the GY-DV700W only. rnSL Lc IEEE1394 : Choose this setting when the VCR should iE be remote controlled from a DV connector 23 equipped video component connected to the DV connector on the rear section of the GY-DV700W. RS232C : Choose this setting for control by means of the VCR remote control signal from the VTR Note: REMOTE connector on the GY-DV700W. • The operation buttons on the GY-DV700W remain effective even when set to IEEE1394 or RS232C. • When the REMOTE SELECT item is set to IEEE1394 or RS232C, ASPECT RATIO will be fixed and "FIX" is displayed. 052: STEP SLOW MODE StEP FIELD FRAME Fd FM Selection of the advance amount in STILL mode. (Frame/Field advance is effective only with an external remote control signal.) FIELD : Field-by-field advance. FRAME : Frame-by-frame advance. FRAME 082: BACK TALLY MODE rtMd OFF ON BLINK oF on bL Selection of the lighting pattern of the BACK TALLY lamp on the rear section during recording. OFF : The lamp is always off. ON : The lamp lights during recording. It remains off until the VTR trigger button is pressed to start the recording. BLINK : The lamp lights during recording. It blinks when the VTR trigger button is pressed to start the recording. BLINK 126: INPUT SELECT CAMERA IEEE1394 vid cA, iE Note: The setting of this item can only be changed in the stop mode or when a cassette is not loaded. Selection of the input video signal. Settings cannot be changed during recording. CAMERA : Camera image is input. IEEE1394 : The image from the DV connector equipped video component connected to the DV connector on the rear section is input. CAMERA 244: LOW CUT LctF OFF CH1 CH2 CH1 & CH2 oF 01 02 on To select whether or not the low frequencies of the audio signal from the audio input connectors are cut. Set to ON to reduce the wind noise of the microphone. OFF : The CH1 and CH2 low frequencies are not cut. CH1 : Only the low frequencies of the audio signal input to the CH1 channel are cut. CH2 : Only the low frequencies of the audio signal input to the CH2 channel are cut. CH1& CH2 : The low frequencies are cut for both CH1 and CH2. OFF 245: SAMPLING RATE 32K 48K snPL 32 48 Note: The setting of this item can only be changed in the stop mode or when a cassette is not loaded. 246: FRONT VOLUME DISABLE ENABLE ENABLE FruL oF on To select the sampling rate for digital PCM audio recording. (Both CH1 and CH2) 32K : Digital recording occurs with 12-bit, 32 kHz sampling 48K : Digital recording occurs with 16-bit 48 kHz sampling. * The DV format offers recording tracks for up to 4 chan- nel when recording using 12-bit, 32 kHz sampling. The GY-DV700W records two of these tracks. The GY- DV700W does not allow after-recording. To select whether or not the front section recording level control should be operative. The front section recording level control only affects the audio signal recorded on CH1. DISABLE : Use of the front section recording level control is disabled. ENABLE : Use of the front section recording level control is enabled. * The CH-1 recording level control on the side section works regardless of the setting. 48K ENABLE