JVC HR-S9911U Instructions - Page 16

Program overlap warning display If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. C Select program, then start playback Press rt to move the highlight bar (arrow) to the program you want to play back, then press OK. ● Playback starts automatically after the selected program is located. Video Navigation Title Screen Example: Program 1 (you have just made) and Program 4 overlap each other A Select program to modify Press rt, then press OK or e. ● You can only select one of the overlapping programs. ● If you do not mind this overlap, press PROG. to finish the timer program setting. The program starting earlier or program with the lower program number will be recorded. B Cancel or change program setting To cancel a program, press CANCEL when the Program screen you do not want is shown. To change a program, press the appropriate button: START+/-, STOP+/-, DATE+/-, CH+/-, DAILY (M-F) (Number key "8"), WEEKLY (Number key "9") and/or SP/EP (p) when the Program screen on which you want to make changes is shown, then press OK or e. ● If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again. Video Navigation A Tape number B Tape title If there is no tape title entered, the earliest recording date will be displayed. C Current page number/total page number D Largest blank space on the tape (Calculated remaining time based on the current tape speed (SP or EP) selected on the VCR) E Recorded programs on this tape F Detailed information of currently selected program (Recording start time, end time, recording length, recording speed, program title and category) If there are no title and category entered, "TITLE" and "CATEGORY" will be displayed. G Current tape position "*" is displayed if the currently selected program and the current tape position are different while tape is not running. H Currently selected program I Program information (Recording start time, date and channel number) When you record a TV program with this VCR, the VCR automatically stores in its memory the recording start time, date, channel information, etc. If the tape is recorded on this VCR for the first time, new tape number and the recording date are also registered. On the tape only the tape number information is recorded. ● Turn on the VCR and TV, and select the VCR channel (or AV mode). ● Set the VCR/TV/CABLE/DBS selector on the Remote to "VCR". Deactivating Video Navigation If you do not want to store program information, you can deactivate the Video Navigation function. A Access Main Menu screen, then Video Navigation screen Press MENU on the Remote. Press rt to move the highlight bar (arrow) to "VIDEO NAVIGATION", then press OK or e. B Deactivate Video Navigation Press rt to move the highlight bar Navigation Playback (arrow) to "NAVIGATION", then press OK or e. You can quickly find programs you have recorded on a tape using Press MENU to return to normal screen. this VCR. You can also select a program to watch, and then automatically search for the beginning of the program. A Load a cassette Inserting the cassette recorded on this VCR. ● The VCR turns on automatically. ● The tape will run for a few seconds while the VCR searches for the tape number. ● If the cassette's record safety tab has been removed, playback begins automatically. B Access Title screen NOTES: ● Video Navigation is possible only with the cassettes recorded on this VCR. ● To record the date and time as the program title in this VCR's memory, make sure the VCR's clock is set correctly before recording. ● To record the program information in this VCR's memory, you must continue to record each program for over the minimum recording time; 5 minutes for the SP mode or 15 minutes for the EP mode. ● During playback or when searching for the beginning of a Press NAVIGATION. ● After pressing NAVIGATION, it may take a few seconds to access the Title screen. ● If there is no cassette loaded, the Find Title screen appears. (੬ pg. 18) program, a VCR might find two different tape numbers recorded on a tape. After you remove this tape, the tape will be assigned just one tape number (the smaller one). After this, the higher tape number will be missing from the memory's tape number list. ● Tape program information is stored in this VCR's memory. If this VCR's memory is damaged and the program information is lost, - 16 - it is impossible to restore that information.Screens for video