JVC HR-S9911U Instructions - Page 9

D Connect Controller to VCR DBS RECEIVER BRAND CODE DBS RECEIVER BRAND CODE Connect the Controller to the CABLE BOX Controller connector JVC (DISH Network) 51 SONY (DSS) 41 on the rear panel. ECHOSTAR (DISH 51 RCA (DSS) 40 E Turn on cable box or DBS receiver Network) Select a channel other than channel 9 on your cable box, or channels 100, 205 on your DBS receiver. F Access Main Menu screen, then Initial Set screen on VCR Press MENU on the Remote. Press rt to move the highlight bar (arrow) to "INITIAL SET", then press OK or e. G Access Cable Box Set screen or DBS Receiver Set screen Press rt to move the highlight bar (arrow) to "CABLE BOX SET" or "DBS RECEIVER SET", then press OK or e. H Select output channel Your selection depends on how the unit is connected to your VCR. ● If the unit is connected to your VCR's ANTENNA IN terminal on the rear panel, Press rt until the channel number representing the cable box's output (CH2 - CH9) or DBS receiver's output (CH3 or CH4) appears on the screen. ● If the unit is connected to your VCR's AUDIO/VIDEO IN connectors on the front panel, press rt until "ON F-1 (FRONT)" appears on the screen. ● If the unit is connected to your VCR's AUDIO/VIDEO IN connectors on the rear panel, press rt until "ON L-1 (REAR)" appears on the screen. ● If you do not use any unit, press rt until "OFF" appears on the screen. I Access Brand Set screen Press OK or e. ● If the Clock Set screen appears, perform "Manual Clock Set" (੬ pg. 7). If you press MENU after the clock has been set, the Brand Set screen appears. For cable box ● If the cable box's channel changes to 9, setting is complete. Press OK. ● If the cable box's channel does not change to 9; A Press rt to move the highlight bar (arrow) to "NO", then press OK or e. B Repeat step 0 until the cable box's channel changes to 9 by entering another code. C If the channel does not change after going through all the code numbers listed for your model of cable box, then try all the other numbers. For DBS receiver ● If the DBS receiver's channel changes to the channel listed below for your brand, setting is complete. Press OK or e. JVC ] 100 SONY ] 205 ECHOSTAR ] 100 RCA ] 205 ● If the DBS receiver's channel does not change as shown above; A Press rt to move the highlight bar (arrow) to "NO", then press OK or e. B Repeat step 0. Playback Basic Playback ● Turn on the VCR and TV, and select the VCR channel (or AV mode). ● Set the VCR/TV/CABLE/DBS selector on the Remote to "VCR". J Enter brand code and perform test A Load a cassette Press the appropriate Number keys on the Remote to enter the brand code from the following list, then press OK or e. CABLE BOX BRAND ARCHER CABLETENNA CABLEVIEW CITIZEN CURTIS DIAMOND GC BRAND GEMINI GENERAL INSTRUMENTS HAMLIN JASCO JERROLD NOVAVISION OAK PANASONIC PULSER RCA REGAL REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH CODE 1, 5, 17 1, 17 15, 16, 17, 21, 25 15, 16, 17, 21, 25 2, 8 1, 17 15, 16, 17, 21, 25 15 1, 4, 6, 11, 12, 15, 28 10, 18, 23 15 1, 4, 6, 11, 12, 15, 28 2, 8 7, 20 13, 14 15, 16, 17, 21, 25 13, 14 10, 18, 23 1, 16, 17 5, 16, 24 2, 8 7, 20 5, 16, 17, 24, 25 13, 14 5, 15, 16, 17, 21, 24, 25 5, 16, 24 1, 4, 16 1, 17 16, 17, 25 3, 9, 22 3, 9, 22 Make sure the window side REW FF is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. ● Do not apply too much pressure when inserting. ● The VCR turns on automatically. ● The tape will run for a few seconds while the VCR searches for the tape number. ● If the cassette's record safety tab has been removed, playback begins automatically. NOTE: When you use the Video Navigation function, operate the VCR only after the tape number is detected; otherwise, you cannot use the Video Navigation function. B Start playback Press PLAY (4). ● The S-VHS indicator lights up when you play back a tape recorded in S-VHS mode or in S-VHS ET mode (੬ pg. 13). CONTINUED ON NEXT PAGE -9-