JVC HR-S9911U Instructions - Page 22
Multi-Brand Remote Control, Changing Remote Control Code, TV Brand Setting
UPC - 046838160684
View all JVC HR-S9911U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Multi-Brand Remote Control When programed (set) with a manufacturer's (brand's) code, this Remote can perform some of the remote control functions of the listed TVs, cable boxes and DBS (Direct Broadcast Satellite) receivers. You can control a JVC TV without setting a brand code. NOTES: ● Some unit's brands have more than one code listed. If after setting, the remote does not operate the unit, try one of the other listed codes. ● Depending on the type of unit, some or all functions cannot be operated using this Remote. ● It is impossible to control a unit that does not have a remote sensor. ● It is not possible to set the Remote for both your cable box and a DBS receiver at the same time. ● Once you have set the Remote to operate a unit, you do not have to set it again until you replace the Remote's batteries. ● If the batteries of the Remote are discharged, the Remote will not be able to control the TV, cable box or DBS receiver. Replace the batteries. TV Brand Setting ● Turn on the VCR and TV, and select the VCR channel (or AV mode). ● Set the VCR/TV/CABLE/DBS selector on the Remote to "TV". A Turn on TV Turn on the TV using the Power button on the TV or its Remote. B Set TV brand code A Press and hold POWER on the Remote. B Press the Number keys to enter your TV's brand code. C Press STOP (8), and release POWER. The TV should turn off. C Operate TV First set the VCR/TV/CABLE/DBS selector to "TV", then press one of the following buttons: POWER, TV/VCR, TV CH+/-, ^ (TV Muting), TV VOL+/-, and the Number keys. ● For some brands, you must press ENTER after having pressed the Number keys to enter a channel number. ● To operate the VCR, set the VCR/TV/CABLE/DBS selector back to "VCR". TV BRAND JVC HITACHI MAGNAVOX MITSUBISHI PANASONIC RCA SHARP CODE 01, 03 10 02 03 04, 11 05 06 TV BRAND SONY SAMSUNG SANYO SEARS TOSHIBA ZENITH CODE 07 12 13 13 08 09 Cable Box or DBS Receiver Brand Setting ● Turn on the VCR and TV, and select the VCR channel (or AV mode). ● Set the VCR/TV/CABLE/DBS selector on the Remote to "CABLE/DBS". A Turn on cable box or DBS receiver Turn on the cable box or DBS receiver using the Power button on the unit or its Remote. B Enter brand code A Press and hold POWER on the Remote. B Press the Number keys to enter your cable box's (or DBS receiver's) brand code. C Press STOP (8), and release POWER. The cable box (or DBS receiver) should turn off. C Operate cable box or DBS receiver First set the VCR/TV/CABLE/DBS selector to "CABLE/DBS", then press one of the following buttons: POWER, TV CH+/-, and the Number keys. ● For some brands, you must press ENTER after having pressed the Number keys to enter a channel number. ● To change the cable box's (or DBS receiver's) channels, press TV CH+/- or the Number keys. (The CH+/- button can be used to change the VCR's channels only.) ● To operate the VCR, set the VCR/TV/CABLE/DBS selector back to "VCR". CABLE BOX BRAND ARCHER CABLETENNA CABLEVIEW CITIZEN CURTIS DIAMOND GC BRAND GEMINI GENERAL INSTRUMENTS HAMLIN JASCO JERROLD NOVAVISION OAK PANASONIC PULSER RCA REGAL REMBRANDT SAMSUNG SCIENTIFIC ATLANTA SIGMA SL MARX SPRUCER STARGATE TELEVIEW TOCOM UNIKA UNIVERSAL VIDEOWAY ZENITH CODE 01, 05, 17 01, 17 15, 16, 17, 21, 25 15, 16, 17, 21, 25 02 01, 17 15, 16, 17, 21, 25 15 01, 04, 06, 11, 12, 15, 28 10, 18, 23 15 01, 04, 06, 11, 12, 15, 28 02 07 13, 14 15, 16, 17, 21, 25 13, 14 10, 18, 23 01, 16, 17 05, 16, 24 02 07 05, 16, 17, 24, 25 13, 14 05, 15, 16, 17, 21, 24, 25 05, 16, 24 01, 04, 16 01, 17 16, 17, 25 03, 09, 22 03, 09, 22 DBS RECEIVER BRAND JVC (DISH Network) ECHOSTAR (DISH Network) SONY (DSS) RCA (DSS) CODE 51 51 41 40 Changing Remote Control Code This Remote is capable of transmitting two different control codes, A code control signals or B code control signals. This Remote is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily change your Remote and VCR to send and respond to B code signals. When using two JVC VCRs, set the two VCRs and their Remotes to different codes, so that the Remotes can operate the VCRs separately. Set the VCR/TV/CABLE/DBS selector on the Remote to "VCR". A Set remote control code for Remote A Press and hold A/B. B Press the Number key "2". C Press STOP (8), and release A/B. ● The Remote now can transmit B code control signals. B Check remote control code for VCR Press and hold 4 on the VCR for more than 5 seconds while the VCR is turned off. The code currently set appears on the display panel. - 22 -