JVC HR-S9911U Instructions - Page 6

Connections and Plug&Play Setting A Check contents Make sure the package contains all of the accessories listed in "Specifications" (੬ pg. 26). B Situate VCR Place the VCR on a stable, horizontal surface. C Connect VCR to TV Antenna or cable Coaxial cable Flat feeder Matching transformer (not supplied) AC power cord S-video Connection (allows you to make the most of the S-VHS picture performance.) If your TV is equipped with an S-video input connector A Perform "RF Connection" previously described. B Connect the supplied S-video cable between the S VIDEO OUT connector on the rear of the VCR and the S-video input connector on the TV. C Connect an audio cable between the AUDIO OUT connectors on the rear of the VCR and the audio input connectors on the TV. ● Even if you are using audio/video cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another. D Perform Plug&Play setup Plug the AC power cord into an AC outlet. Do not turn on the VCR. The clock and tuner channels will be set automatically. The time and date can be set automatically by the clock setting data transmitted from one of the regular TV broadcast channels. We call this TV channel the "host channel" and it is a PBS channel in your area. ATTENTION: ● If you use a cable box, Plug&Play will not function; set the clock and tuner channels separately (੬ pg. 7 - 8). ● Depending on area or reception conditions, the VCR may not receive the Auto clock setting data from a PBS channel. If this function is taking a considerable amount of time, it may be necessary to perform the procedure in "Semiauto Clock Set" (੬ pg. 7) or "Manual Clock Set" (੬ pg. 7). During Initial Auto Clock Set "Auto" blinks. AC outlet Back of VCR Audio/video cable (supplied) To audio/video input connectors TV To S-video input S-video cable connector (supplied) To 75 ⍀ terminal RF cable (supplied) RF Connection A Disconnect the TV antenna from the TV. B Connect the TV antenna cable to the ANTENNA IN terminal on the rear of the VCR. C Connect the supplied RF cable between the TV OUT terminal on the rear of the VCR and the TV's antenna input terminal. AV Connection (improves picture quality during tape playback.) If your TV is equipped with audio/video input connectors A Connect the antenna, VCR and TV as shown in the illustration. B Connect the supplied audio/video cable between the AUDIO/ VIDEO OUT connectors on the rear of the VCR and the audio/ video input connectors on the TV. During Auto Channel Set The channel numbers are displayed as they are scanned and set. Plug&Play Completed The current time is displayed. What to do if Plug&Play setting failed ● If an incorrect time is displayed on the display panel, perform the procedure in "Semiauto Clock Set" (੬ pg. 7) or "Manual Clock Set" (੬ pg. 7). ● If "- -:- -" appears on the display panel, ensure that the antenna cable is connected correctly. Then turn on and off the VCR; the Plug&Play setting will be automatically reactivated. If Plug&Play setting is not performed though the antenna cable is connected correctly, perform the procedure in "Manual Clock Set" (੬ pg. 7) and "Auto Channel Set" (੬ pg. 8) or "Manual Channel Set" (੬ pg. 8). E Set VCR channel The VCR channel is the channel on which you can watch the picture from the VCR on the TV when using the RF connection. Press POWER to turn off the VCR, then press STOP/EJECT (0) on the VCR for more than 5 seconds. "3CH" appears on the display panel. Press CH+/- to select "3CH", "4CH" or "- CH"(OFF), then press OK. ● The VCR channel is preset to "3CH". Set to "4CH" if 3CH is used for broadcasting in your area. F Final preparation for use Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. You can now perform basic playback or basic recording. ● If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel. -6-