JVC VN-H137UA Instruction Manual - Page 38

Monitor Output, Set values: ON, Monitor Output for Installation mode, Procedure, the [Encoding]

Get JVC VN-H137UA PDF manuals and user guides View all JVC VN-H137UA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Internet Explorer Setting Settings (continued) Encoding Page (continued) D Monitor Output Change monitor output settings. [Set values: ON, OFF] There are restrictions on the encoder settings which can be set to [ON]. To output to a monitor, select "single encode" and set Framerate using one of the following. 1920x1080 5 fps or below 1280x960 or 1280x720 15 fps or below 640x480, 640x360 or 320x240 30 fps or below Memo: ● Images that are in the aspect ratio of 16:9 are compressed horizontally to 4:3 when output. When an aspect ratio of 4:3 is selected, the distributed image is 4:3, but the image output to the monitor is the same as that of when aspect ratio 16:9 is selected. Monitor Output (for Installation) mode To adjust angle of view and check focus when setting up the camera, press and hold the [FOCUS ASSIST] button to output the video image from the monitor output terminal. The image will be output even if [Monitor Output] is set to [OFF] in encode settings. In Monitor Output (for Installation) mode, vertical gray lines are inserted on either side of the image. This is to indicate the area to be captured in aspect ratio 4:3 and is not a malfunction. Procedure Press and hold the [FOCUS ASSIST] button on the camera for 5 or more seconds. The camera [STATUS] indicator lamp will alternately flash between orange and green. (The amount of time the lamp is lit up in orange is twice as long as when it is lit up in green.) At the same time, the camera enters focus assist mode. Connect the signal from the monitor output terminal to the monitor and perform adjustment of the view angle and focus. Once manual adjustment is finished, press and hold the [FOCUS ASSIST] button for 5 or more seconds to release Monitor Output (for Installation) mode. Check that the [Status] indicator lamp is glowing green. Memo: ● Release Monitor Output (for Installation) mode before adjusting the autofocus. ● When in Monitor Output (for Installation) mode, the [Encoding] page continues to show [Monitor Output] as set to [OFF]. ● When changing the encode settings, be sure to press and hold the [FOCUS ASSIST] button for 5 or more seconds to release the monitor output mode. ● The aspect ratio 16:9 capture area is output in Monitor Output. When aspect ratio 4:3 is selected in Encoding settings, perform adjustment to the viewing angle so that the subject fits inside the vertical gray lines on either side of the Monitor Output image. * The [Set values] in bold letters are factory defaults. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
38
Internet Explorer Setting
Encoding Page (continued)
* The [Set values] in bold letters are factory defaults.
Settings (continued)
D
Monitor Output
Change monitor output settings.
[Set values: ON
, OFF
]
There are restrictions on the encoder settings which can be set to [ON].
To output to a monitor, select "single encode" and set Framerate
using one of the following.
1920x1080 5 fps or below
1280x960 or 1280x720 15 fps or below
640x480, 640x360 or 320x240 30 fps or below
Memo:
●
Images that are in the aspect ratio of 16:9 are compressed
horizontally to 4:3 when output. When an aspect ratio of 4:3 is
selected, the distributed image is 4:3, but the image output to the
monitor is the same as that of when aspect ratio 16:9 is selected.
Monitor Output (for Installation) mode
To adjust angle of view and check focus when setting up the
camera, press and hold the [FOCUS ASSIST] button to output the
video image from the monitor output terminal. The image will be
output even if [Monitor Output] is set to [OFF] in encode settings.
In Monitor Output (for Installation) mode, vertical gray lines are
inserted on either side of the image. This is to indicate the area to
be captured in aspect ratio 4:3 and is not a malfunction.
Procedure
Press and hold the [FOCUS ASSIST] button on the camera for 5 or
more seconds. The camera [STATUS] indicator lamp will
alternately flash between orange and green.
(The amount of time the lamp is lit up in orange is twice as long as
when it is lit up in green.)
At the same time, the camera enters focus assist mode.
Connect the signal from the monitor output terminal to the monitor
and perform adjustment of the view angle and focus.
Once manual adjustment is finished, press and hold the [FOCUS
ASSIST] button for 5 or more seconds to release Monitor Output
(for Installation) mode.
Check that the [Status] indicator lamp is glowing green.
Memo:
●
Release Monitor Output (for Installation) mode before adjusting
the autofocus.
●
When in Monitor Output (for Installation) mode, the [Encoding]
page continues to show [Monitor Output] as set to [OFF].
●
When changing the encode settings, be sure to press and hold
the [FOCUS ASSIST] button for 5 or more seconds to release
the monitor output mode.
●
The aspect ratio 16:9 capture area is output in Monitor Output.
When aspect ratio 4:3 is selected in Encoding settings, perform
adjustment to the viewing angle so that the subject fits inside the
vertical gray lines on either side of the Monitor Output image.