Home » Konica Minolta Manuals » Printers » Konica Minolta C3080P » Manual Viewer

Konica Minolta C3080P AccurioPress C2070/C3080 Series Daily Maintenance Guide - Page 118

When the there is no idle registration, The adjustment value is registered in the lowest idle number.

View all Konica Minolta C3080P manuals

Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

3.6 Details of quality adjustment items 3 10 Reverse the top and bottom of the scanned test chart, then load it on the Original Glass. % Turn the arrow mark of the test chart forward, then face the print side downward. % Take the test chart away from the vertical size guide by 2 inches (5 cm), then push it against the horizontal size guide to load the test chart. % Place about 10 sheets of blank copy paper on the test chart. % Close the ADF. 11 Press [Start] on the screen. The second scan is carried out, and the density balance adjustment value is registered. 12 When the adjustment is completed normally, the adjustment value is automatically registered, and the screen shown below is displayed. Select whether to output the adjustment chart for confirmation purposes. % The adjustment value is registered according to the following conditions. When the there is an idle registration: The adjustment value is registered in the lowest idle number. When the there is no idle registration: The adjustment value is overwritten to the number that matches the following conditions. If multiple values match the conditions, they are overwritten preferentially from the condition of a low number. (1) Adjustment value of same screen, same paper type, same weight, and old date (2) Adjustment value of same screen, same paper type, and old date (3) Adjustment value of same screen and old date AccurioPress C2070/C2070P/C2060/C3080/C3080P/C3070, AccurioPrint C2060L/C3070L 3-47

Section	Page
Table of contents	4
1 Daily Care	7
1.1 About Daily Care	7
Care Timing	7
Care requirements	7
1.2 Cleaning the Duplex Part	8
1.3 Cleaning Main Body Tray	11
1.4 Cleaning Multi Bypass Tray MB-506 or Multi Bypass Tray MB-508	13
1.5 Cleaning Paper Feed Unit PF-602m	14
1.6 Cleaning Paper Feed Unit PF-707 or Paper Feed Unit PF-707m	18
1.7 Cleaning Large Capacity Unit LU-202m, Large Capacity Unit LU-202XL, or Large Capacity Unit LU- 202XLm	20
2 Both Sides Adjust	23
2.1 What is Both Sides Adjust?	23
2.2 Adjustment flow to use paper of a new brand, weight, or size	24
2.2.1 Adjustment Timing	24
2.2.2 Adjustment Order	24
2.3 Regular adjustment flow	25
2.3.1 Adjustment Timing	25
2.3.2 Adjustment Order	25
2.3.3 Periodical Both Sides Adjustment Function	26
2.4 Adjustment flow for each job	27
2.4.1 Adjustment Timing	27
2.4.2 Adjustment Order	27
2.5 How to Operate the Both Sides Adj. Item	28
2.5.1 Finely adjust the side guide plates of the paper tray (for PF-707/PF-707m/PF- 602m)	28
2.5.2 [Front] Adjustment	31
2.5.3 [Gap] Adjustment (Back side adjustment)	36
2.5.4 [Scan Meas.] Adjustment	41
2.5.5 [Rotate/Skew] Adjustment	51
2.5.6 [AutoMeasure] Adjustment	58
2.5.7 Registering Paper Profile	62
2.5.8 Back Side Fine Adjustment	64
2.5.9 [Periodical Both Sides Adj.]	69
3 Quality Adj.	73
3.1 Quality Adjustment for Image Controller IC-603/ Image Controller IC-605	73
3.2 Regular adjustment flow (Standard)	74
3.2.1 Adjustment timing	74
3.2.2 Adjustment sequence	74
3.3 Regular adjustment flow (High accuracy)	75
3.3.1 Adjustment Timing	75
3.3.2 Adjustment Order	75
3.4 Adjustment flow to use a new type of paper	76
3.4.1 Adjustment timing	76
3.4.2 Adjustment sequence	76
3.5 Adjustment Flow when changing the screen	77
3.5.1 Adjustment timing	77
3.5.2 Adjustment sequence	77
3.6 Details of quality adjustment items	78
3.6.1 Setting of the Custom Screen	78
3.6.2 [Gamma Automatic Adjustment]	80
Performing [Gamma Automatic Adj.]	80
3.6.3 [Density Balance Adjustment] (for i1Pro, i1Pro2, or i1iSisXL)	82
Saving the measured data of the density balance	90
3.6.4 [Density Balance Adjustment] (for FD-5BT)	92
3.6.5 Registering the adjusted value of the density balance in the machine	103
3.6.6 [Density Balance Auto. Adj.]	110
3.6.7 [Maximum Density Adjustment]	120
3.6.8 [Maximum Density Adjustment] (for i1Pro/i1Pro2)	121
3.6.9 [Maximum Density Adjustment] (for FD-5BT)	130
3.6.10 [Max. Density Auto Adj.]	138
3.6.11 Checking the Color Density Control Setting	141
3.6.12 [Color Density Manual Control]	144
3.6.13 About Controller Calibration	147
Executing Calibration	148
3.6.14 About Exact Color calibration	154
Executing Exact Color: Color Centro	155
Executing Exact Color: Touch panel	162
3.6.15 About G7 Calibration	165
Executing G7 Calibration: Color Centro	166
Executing G7 Calibration: Touch panel	172