Marantz SR5003 SR5003 User Manual - English - Page 12

ENGLISH NAMES AND FUNCTION BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS REAR PANEL q w e rt y FM (75Ω) GND AM ANTENNA INPUT 1(TV) INPUT 2(DVD) INPUT 3(VCR) OUTPUT L SL C SBL ZONE A TV DVD L VCR DSS R R (AUX 2) SR SW 7.1CH INPUT SBR RS-232C SPEAKER C OFF ON OUT IN OUT TAPE IN OUT VIDEO INPUT 1(TV) INPUT 3(VCR) COMPONENT VIDEO S-VIDEO AUDIO CD/CDR TV(1) 4 DVD(2) VCR IN(3) VCR OUT DSS(4) MONITOR OUT Y CB/PB CR/PR DIGITAL IN DIGITAL FLASHER IN REMOTE CONT. REC/ZONE B INPUT 2(DVD) SIRIUS IN 5 Y CB/PB CR/PR OUTPUT 1 Y CB/PB CR/PR OUTPUT 2 IN OUT 1 2 3 OUT DC OUT OUT AC OUTLETS 120V 60Hz L SL C SBL R L R L R L R L UNSWITCHED 1.25A 150W MODEL NO. SR5003 FRONT A FRONT B SURROUND R SR SW SBR FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS SPEAKER SYSTEMS PRE OUT CENTER SURROUND BACK SPEAKER C/ ZONE SPEAKER A SWITCHED 1.25A 150W AC IN @1@0 !9!8!7!6 !5 !3 !1 !4 !2 !0o i u q FM antenna terminal (75 ohms) Connect an external FM antenna with a coaxial cable, or a cable network FM source. AM antenna and ground terminals Connect the supplied AM loop antenna. Use the terminals marked "AM" and "GND". The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception. w HDMI INPUT/OUTPUT The unit has 3 HDMI inputs and 1 HDMI output.The input function can be selected from the OSD menu system. (See page 27) e AUDIO IN/OUT (CD, TAPE, CD-R, TV, DVD, VCR, DSS) These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. r VIDEO IN/OUT (TV, DVD, VCR, DSS) These are the video inputs and outputs. There are 4 video inputs and 1 video output and each one includes both composite video and S-video configurations. Connect VCRs, DVD players, and other video components to the video inputs. The video output channel can be used to be connected to video tape recorders for making recordings. t MONITOR OUT This is a monitor output and each one includes both composite video and S-video configurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections. y COMPONENT VIDEO INPUT/ OUTPUT If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the unit. This unit has two component video input connectors to obtain the color information (Y, CB, CR) directly from the recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT VIDEO jack. u XM terminal Connect to the XM Mini-Tuner and Home Dock. (See page 22) i AC INLET Plug the supplied power cable into this AC INLET and then into the power outlet on the wall. This unit can be powered by 120V AC only. o SIRIUS terminal Connect to the SiriusConnectTM Home Tuner. (See page 22) !0 AC OUTLETS Connect the AC power cables of components such as a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power only when the unit is turned on and is useful for components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the unit is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch. Caution: • In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the unit is turned on. • The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply. !1 REMOTE CONT. IN/OUT terminals Connect to a Marantz component equipped with remote control (RC-5) terminals. !2 FLASHER IN (Flasher input terminal) These terminals are to control the unit from each ZONE. Connect the control signal from a Keypad, etc. !3 DC TRIGGER output terminal Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc...) Use the system OSD setup menu to determine the conditions by which these jack will be active. Note: This output voltage is for (status) control only, It is not sufficient for drive capability. !4 DIGITAL INPUT (DIGITAL IN 1-5) / OUTPUT (optical) These are the digital audio inputs and output. The unit has 2 digital inputs with coaxial jacks, 3 with optical jacks. The inputs accept digital audio signals from a CD, DVD, or other digital source component. For digital output, this is 1 optical output. The digital outputs can be connected to MD recorders, CD recorders, or other similar components. In addition, this digital output can be used as ZONE B output. !5 Speaker outputs terminals Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers. Note: You can use surround back speaker terminals as ZONE SPEAKER A terminals, when you use no surround back speaker. !6 ZONE A Outputs These are the audio output jacks for the ZONE A. Connect these jacks to optional audio power amplifiers to listen the source selected by the ZONE system in a remote room. !7 SPEAKER C SELECTOR SWITCH The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. For connection and use, see page 20. !8 Preamp Outputs (L, R, SL, SR, SBL, SBR, C) Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power amplifiers. !9 Subwoofer Output Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input. If you are using two subwoofers, either powered or with a 2 channel subwoofer amplifier, connect a "Y" connector to the subwoofer output jack and run one cable from it to each subwoofer amplifier. @0 RS-232C The RS-232C port is to be used in conjunction with an external controller to control the operation of the unit by using an external device. @1 7.1 CHANNEL or AUX2 INPUT By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with 5.1 channel or 7.1 channel outputs. 9 SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS