Marantz SR5003 SR5003 User Manual - English - Page 17
Connecting Hdmi Components - manual
View all Marantz SR5003 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 17 highlights
NAMES AND FUNCTION BASIC CONNECTIONS BASIC OPERATION ENGLISH CONNECTING HDMI COMPONENTS DVD player HDMI OUTPUT VIDEO PROJECTOR HDMI INPUT FM (75Ω) GND AM ANTENNA INPUT 1(TV) INPUT 2(DVD) INPUT 3(VCR) OUTPUT L SL C SBL ZONE A TV DVD L VCR DSS R R (AUX 2) SR SW 7.1CH INPUT SBR RS-232C SPEAKER C OFF ON OUT IN OUT TAPE IN OUT VIDEO INPUT 1(TV) INPUT 3(VCR) COMPONENT VIDEO S-VIDEO AUDIO CD/CDR TV(1) 4 DVD(2) VCR IN(3) VCR OUT DSS(4) MONITOR OUT Y CB/PB CR/PR DIGITAL IN DIGITAL FLASHER IN REMOTE CONT. REC/ZONE B INPUT 2(DVD) SIRIUS IN 5 Y CB/PB CR/PR OUTPUT 1 Y CB/PB CR/PR OUTPUT 2 IN OUT 1 2 3 OUT DC OUT OUT AC OUTLETS 120V 60Hz L SL C SBL R L R L R L R L UNSWITCHED 1.25A 150W MODEL NO. SR5003 FRONT A FRONT B SURROUND R SR SW SBR FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS SPEAKER SYSTEMS PRE OUT CENTER SURROUND BACK SPEAKER C/ ZONE SPEAKER A SWITCHED 1.25A 150W AC IN SATELLITE TUNER HDMI OUTPUT HDMI JACKS This unit has three HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. This unit is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output. Select an input source from the OSD menu system. (See page 27) Notes: • When the HDMI output is connected to a display monitor that does not support HDCP*, signals are not output. To view images in HDMI, it is necessary to connect to a display that supports HDCP. • There may be no image output if connected to a TV or display that is not compatible with the above format. • Refer to the instruction manual of the TV or display to be connected to the unit for detailed information regarding the HDMI terminal. * HDCP: High-bandwidth Digital Content Protection CONNECTING HDMI COMPONENTS An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on the DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack. Notes: • Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way. • When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output. • Some source devices such as DVD players or set top box do not support HDMI repeater operations like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors. • When multiple components are connected to this unit, turn power to unused components off to prevent interference between them. • Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables. • If the DVD player that does not support HDMI 1.1 or later is connected to the unit, multi channel PCM playback is not possible even with DVD-Audio disks. • If the Super Audio CD player that does not support HDMI 1.2 or later is connected to the unit, DSD playback is not possible even with Super Audio CD. (*DSD: Direct Stream Digital) • The following functions are not available when the unit is connected to equipment that does not support HDMI 1.3a. • Deep Color • x.v. Color • Bitstream audio signal decoding, as for Dolby Digital Plus, Dolby TrueHD, DTS-HD, and so on For details, refer to the user's manuals of connected equipment. • Multi channel PCM signals and audio signals of 64 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jack. • Depending on the quiality of the cable used, the HDMI signal may be affected by noise. ADVANCED CONNECTIONS SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 14