Marantz SR5003 SR5003 User Manual - English - Page 45
Advanced Operation
View all Marantz SR5003 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 45 highlights
NAMES AND FUNCTION BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS ENGLISH ADVANCED OPERATION AMP OPERATION USING THE SLEEP TIMER DISPLAY MODE RECORDING AN ANALOG SOURCE In normal operation, the audio or video source selected for listening through this unit is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD/CD-R OUT and VCR OUT in the record mode. SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT To program this unit for automatic standby, press the SLEEP button on the remote controller. Each press of the button will increase the time before shut down in the following sequence. OFF 10 20 30 40 50 120 110 100 90 80 70 60 The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows "SLEEP OFF" and the SLEEP indicator will disappear. You can select the display mode for the front display of the unit. To select this mode, press the DISPLAY on the remote controller or the front panel. When this button is pressed, the display mode is switched in the following sequence. Normal → Volume → Auto display OFF → Display OFF → Normal Mode Normal mode: The following three mode types are displayed. w Displays the selected input function. If the function has been renamed using the Function Rename feature (see page 28), the renamed name appears on the display. w Displays the input mode set via the Function Input Setup feature. (See page 27) w Displays the status of the selected surround mode. Volume mode: The input function and input mode are displayed in the upper part, and the current volume level is displayed in the lower part. Auto Display Off mode: The display is off. But, if you make a change to the unit such as the input or surround mode, the display will show that change, then go back to off after about 3 seconds. When changing the volume, it is not displayed. Display Off mode: The display is off completely. Note: • Only the "DISP" indicator will be illuminated on the front display in display off condition. To record the input source signal you are currently watching or listening to 1. 1. 1. Select the input source to record by turning the INPUT FUNCTION SELECTOR knob on the front panel or simply press the input selector buttons on the remote controller. The input source is now selected and you may watch or listen to it as desired. 2. The currently selected input source signal is output to the TAPE OUT, CD/CD-R OUT and VCR OUT outputs for recording. 3. Start recording to the recording component as desired. Notes: • When connecting only digital signal input, output cannot be made to the TAPEOUT, CD/CDR OUT or VCR1 OUT terminals. When using recording functions, be sure to also make connections for analog signal input. • No conversion is made from Video signal input to S-Video signal output or from S-Video signal input to Video signal output. Always use the same signal type for both input and output. • Video or audio signals input to HDMI input terminals cannot be recorded. If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source as following procedures. Press the AMP button and press the A/D button. When this button is pressed, the input mode is switched in the following sequence. Auto → HDMI → Digital → Analog → Auto Auto mode: The types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. HDMI mode: HDMI mode can be selected only when an HDMI input has been assigned as an input source. When "HDMI AUDIO" under PREFERENCE of the SETUP MENU is set to "THROUGH", the HDMI mode cannot be selected. Digital mode: The input signal is fixed to an assigned digital input terminal. Analog mode: The analog input jacks are selected. This selection is temporary and will not be stored in memory. To store changes to the input mode, select "1. INPUT SETUP" from the MAIN MENU. (See page 27) SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 42