Motorola DCP501 User Guide - Page 72

Test Tone Adjust, To use the Test Tone Adjust feature

Get Motorola DCP501 - DVD Player / AV Receiver PDF manuals and user guides
UPC - 612572007839
View all Motorola DCP501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

62 Operation Test Tone Adjust The Test Tone option allows you to hear test tones and adjust the level of these tones on speakers connected to the DCP501 to properly balance the sound system with the listening area. For full benefit, Test Tone Adjust should be performed when the DCP501 is in Dolby-Digital or dts mode. You can be in any audio mode except stereo to enter the Test Tone Adjust menu. You can only adjust the test tone levels for the speakers that are used in the audio mode you have selected. For example, Dolby 3 Channel Stereo uses left, right, and center speakers. You can adjust the test tones for these three speakers, but not for either of the surround speakers. In any of the full surround modes, you can adjust all five test tone levels - left, right, center, right surround, left surround. You are not allowed to adjust any of the test tones when stereo mode is selected. Set the base volume level of each speaker with this option. Perform this operation while sitting at the listening position. The factory setting is 0 d B . As the tone is played through each speaker, the current setting flashes. Use the DCP501 remote control or front panel CURSOR left/right (< >) to adjust the volume level of each speaker so that all speaker volumes sound the same. It is not necessary to press SETUP or OK to record your settings for each speaker. To use the Test Tone Adjust feature: 1 Press SETUP to display the DCP501 M A I N S E T U P menu on your TV or A U D I O S E T on the DCP501 display. On-screen Display DCP501 Display * MA I N SETUP * XAUDI O SET UP D V D SET UP CAT V RE CORD CAT V C H A N N E L EXI T S C A N AUDI O S E T DCP501 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
62
Operation
DCP501 User Guide
*
M A I
N
S
E
T
U
P
*
A
U D I
O
S
E
T
U P
D
V
D
S
E
T
U P
C
A T
V
R E
C O R D
C
A T
V
C H
A N N E
L
S
C A N
E
X
I
T
Test Tone Adjust
The Test Tone option allows you to hear test tones and adjust the level of these tones on
speakers connected to the DCP501 to properly balance the sound system with the listening area.
±
For full benefit, Test Tone Adjust should be performed when the DCP501 is in Dolby-Digital
or dts mode.
±
You can be in any audio mode except stereo to enter the Test Tone Adjust menu. You can
only adjust the test tone levels for the speakers that are used in the audio mode you have
selected. For example, Dolby 3 Channel Stereo uses left, right, and center speakers. You can
adjust the test tones for these three speakers, but not for either of the surround speakers. In
any of the full surround modes, you can adjust all five test tone levels —
left, right, center,
right surround, left surround. You are not allowed to adjust any of the test tones when
stereo mode is selected.
±
Set the base volume level of each speaker with this option.
±
Perform this operation while sitting at the listening position. The factory setting is
0 dB.
As the tone is played through each speaker, the current setting flashes. Use the DCP501 remote
control or front panel
CURSOR
left/right (
<
>
) to adjust the volume level of each speaker so that
all speaker volumes sound the same.
It is not necessary to pres
s
SETUP
or
OK
to record your settings for each speaker.
To use the Test Tone Adjust feature:
1
Press
SETUP
to display the DCP501
MAIN SETUP
menu on your TV or
AUDIO SET
on
the DCP501 display.
On-screen Display
DCP501 Display
A U D I
O
S
E
T