Motorola DCP501 User Guide - Page 90

Using the DCP501 Tuner, Tuning Radio Stations

Get Motorola DCP501 - DVD Player / AV Receiver PDF manuals and user guides
UPC - 612572007839
View all Motorola DCP501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

80 Operation Using the DCP501 Tuner This section describes: How to tune radio stations How to Program the DCP501 to tune to your favorite stations with the preset option Tuning Radio Stations To tune the radio on the DCP501: 1 Press SOURCE to tuner or press AM/FM. The DCP501 displays: The last radio station tuned The radio band- AM or FM (also shown on your TV) The preset number assigned to that station if one has been assigned 2 Press AM/FM to select the radio band. 3 Press tune ST on the front of the DCP501 or ( ) on the remote control to change the frequency. The frequency changes in 200kHz steps in FM and 10kHz steps in AM. Press and hold tune on either the DCP501 front panel or the DCP501 remote control and DCP501 display A U T O icon turns on and the DCP501 scans to the next radio station. If the tuned signal received is strong, the T U N E D icon turns on. For a stereo FM station, the S T icon also turns on. If the signal is weak, S T (stereo) flashes. Press FM MODE to improve the sound, which causes the receiver to operate in monaural (mono) mode, and the S T icon turns off. Press FM MODE again to return to stereo operation. Note: The red S T (stereo) icon, which corresponds to AM/FM broadcasts, is different from the S T (stereo) icon that corresponds to audio playback from all other sources. Presetting Radio Stations You can enter up to 30 preset stations to quickly access your favorite radio station. The 30 stations can be assigned to any combination of AM and FM stations that you would like. To preset radio stations with the DCP501 tuner: 1 Tune to the desired radio station. 2 Press SELECT or OK. The P R E S E T icon flashes at the same time as the station number below it, for example 1 0 5 . 3. 3 Press CHANNEL/PRESETST to select the desired preset number to store the station on or directly enter the preset number using the numeric buttons on your DCP501 remote control. 4 Press SELECT or OK to accept your changes. The P R E S E T icon and the preset number stop flashing. A new preset can be stored over an old one by following the same procedure. DCP501 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
80
Operation
DCP501 User Guide
Using the DCP501 Tuner
This section describes:
±
How to tune radio stations
±
How to Program the DCP501 to tune to your favorite stations with the preset option
Tuning Radio Stations
To tune the radio on the DCP501:
1
Press
SOURCE
to tuner or press
AM
/
FM
. The DCP501 displays:
±
The last radio station tuned
±
The radio band—
AM or FM (also shown on your TV)
±
The preset number assigned to that station if one has been assigned
2
Press AM/FM to select the radio band.
3
Press tune
on the front of the DCP501 or (
) on the remote control to change the
frequency. The frequency changes in 200kHz steps in FM and 10kHz steps in AM. Press and
hold tune on either the DCP501 front panel or the DCP501 remote control and DCP501
display
AUTO
icon turns on and the DCP501 scans to the next radio station.
If the tuned signal received is strong, the
TUNED
icon turns on. For a stereo FM station,
the
ST
icon also turns on. If the signal is weak,
ST
(stereo) flashes. Press
FM MODE
to
improve the sound, which causes the receiver to operate in monaural (mono) mode, and the
ST
icon turns off. Press
FM MODE
again to return to stereo operation.
Note: The red
ST
(stereo) icon, which corresponds to AM/FM broadcasts, is different from
the
ST
(stereo) icon that corresponds to audio playback from all other sources.
Presetting Radio Stations
You can enter up to 30 preset stations to quickly access your favorite radio station. The 30
stations can be assigned to any combination of AM and FM stations that you would like. To
preset radio stations with the DCP501 tuner:
1
Tune to the desired radio station.
2
Press
SELECT
or
OK
. The
PRESET
icon flashes at the same time as the station number
below it, for example
105.3
.
3
Press
CHANNEL
/
PRESET
to select the desired preset number to store the station on or
directly enter the preset number using the numeric buttons on your DCP501 remote control.
4
Press
SELECT
or
OK
to accept your changes. The
PRESET
icon and the preset number stop
flashing.
A new preset can be stored over an old one by following the same procedure.