Home » Netgear Manuals » Modems » Netgear DGND3700v2 » Manual Viewer

Netgear DGND3700v2 [English]: DGND3700v2 User Manual(PDF) - Page 97

Wireless Repeating Function, Wireless Repeater

Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2 local computers. To configure this mode, you have to know the MAC addresses of the child repeater access point. Wireless Repeater. The wireless modem router sends all traffic from its local wireless or wired computers to a remote access point. To configure this mode, you have to know the MAC address of the remote parent access point. The DGND3700v2 wireless modem router is always in dual-band concurrent mode, unless you turn off one radio. Be aware that if you enable the wireless repeater in either radio band, the wireless base station or wireless repeater cannot be enabled in the other radio band. However, if you enable the wireless base station in either radio band and use the other radio band as a wireless wireless modem router or wireless base station, dual-band concurrent mode is not affected. For you to set up a wireless network with WDS, the following conditions have to be met for both access points: • Both access points have to use the same SSID, wireless channel, and encryption mode. • Both access points have to be on the same LAN IP subnet. That is, all the access point LAN IP addresses are in the same network. • All LAN devices (wired and wireless computers) have to be configured to operate in the same LAN network address range as the access points. Wireless Repeating Function Select Advanced > Advanced Setup > Wireless Repeating Function to view or change wireless repeater settings for the wireless modem router. • Enable Wireless Repeating Function. Select the check box for the 2.4 GHz or 5 GHz network to use the wireless repeating function. Advanced Settings 97

Section	Page
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2	1
Contents	3
1. Hardware Setup	7
Label	11
Front Panel	13
Position Your Wireless Router	16
ADSL Microfilters	17
One-Line ADSL Microfilter (Not Included)	17
Summary	18
Verify the Cabling	19
2. Get Started with NETGEAR Genie	21
Use Standard TCP/IP Properties for DHCP	22
Gather ISP Information	22
Wireless Devices and Security Settings	22
NETGEAR Genie Setup	23
Use NETGEAR Genie after Installation	24
Upgrade Wireless Modem Router Firmware	24
Wireless Modem Router Dashboard (Basic Home Screen)	25
Add Wireless Devices or Computers to Your Network	26
Manual Method	26
Wi-Fi Protected Setup (WPS) Method	26
3. Genie Basic Settings	28
Internet Basic Settings Screen Fields	29
Attached Devices	31
Parental Controls	32
USB Storage (Basic Settings)	33
ReadySHARE Printer	34
Basic Wireless Settings	34
Wireless Settings Screen Fields	36
Change WPA Security Option and Passphrase	37
Guest Network Wireless Security Options	39
4. Genie Advanced Home	41
Setup Wizard	42
WPS Wizard	43
Setup Menu	44
ADSL Setup	45
Default DMZ Server	47
Change the MTU Size	48
Use the Wireless Modem Router as a DHCP Server	51
Address Reservation	52
Quality of Service (QoS) Setup	53
5. USB Storage	58
ReadySHARE Access	59
File-Sharing Scenarios	60
USB Storage Basic Settings	61
Add or Edit a Network Folder	62
USB Storage Advanced Settings	63
Safely Remove a USB Drive	65
Media Server Settings	65
Specify Approved USB Devices	66
Connect to the USB Drive from a Remote Computer	67
Access the Wireless Modem Router’s USB Drive Remotely Using FTP	67
6. USB Printer Control	68
Control Center Configuration	70
USB Printer	70
Scan with a Multifunction Printer	71
USB Speaker	71
7. Security	72
Firewall Rules	74
8. Administration	80
View Wireless Modem Router Status	82
Wireless Modem Router Information	82
Internet Provider (WAN) Setup	82
Wireless Settings (2.4 GHz and 5 GHz)	85
Guest Network (2.4 GHz and 5 GHz)	86
View Logs of Web Access or Attempted Web Access	86
Manage the Configuration File	87
Back Up Settings	88
Restore Configuration Settings	88
Erase	88
Set Password	89
Password Recovery	89
Diagnostics	90
9. Advanced Settings	92
Wireless Repeating Function	97
Set Up the Base Station	98
Set Up a Repeater Unit	99
Port Forwarding and Triggering	100
Remote Computer Access Basics	100
Port Triggering to Open Incoming Ports	101
Port Forwarding to Permit External Host Communications	103
How Port Forwarding Differs from Port Triggering	104
Set Up Port Forwarding to Local Servers	104
Add a Custom Service	106
Edit or Delete a Port Forwarding Entry	106
Set Up Port Triggering	107
Dynamic DNS	109
Static Routes	111
USB Settings	114
Universal Plug and Play	114
IPv6	116
Traffic Meter	116
10. Troubleshooting	119
Sequence to Restart Your Network	120
Check Ethernet Cable Connections	120
Wireless Settings	120
Network Settings	120
Troubleshoot with the LEDs	121
Power LED Is Off or Blinking	121
Power LED Stays Red	121
LEDs Never Turn Off	122
Internet or Ethernet Port LEDs Are Off	122
Wireless LEDs Are Off	122
The Push 'N' Connect (WPS) Button Blinks Red	122
Cannot Log In to the Router	123
Cannot Access the Internet	123
Troubleshoot PPPoE	125
Troubleshoot Internet Browsing	125
Changes Not Saved	126
Incorrect Date or Time	126
Wireless Connectivity	126
Wireless Signal Strength	127
Restore the Factory Settings and Password	127
Troubleshoot Your Network Using the Ping Utility	127
Test the LAN Path to Your Router	127
Test the Path from Your Computer to a Remote Device	128
A. Supplemental Information	130
Factory Settings	130
Technical Specifications	132
B. Notification of Compliance	134

Match case Limit results 1 per page

Advanced Settings

N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2

local computers. To configure this mode, you have to know the MAC addresses of the child

repeater access point.

Wireless Repeater

. The wireless modem router sends all traffic from its local wireless or

wired computers to a remote access point. To configure this mode, you have to know the

MAC address of the remote parent access point.

The DGND3700v2 wireless modem router is always in dual-band concurrent mode, unless

you turn off one radio. Be aware that if you enable the wireless repeater in either radio band,

the wireless base station or wireless repeater cannot be enabled in the other radio band.

However, if you enable the wireless base station in either radio band and use the other radio

band as a wireless wireless modem router or wireless base station, dual-band concurrent

mode is not affected.

For you to set up a wireless network with WDS,

he following conditions have to be met for

both access points:

•

Both access points have to use the same SSID, wireless channel, and encryption mode.

•

Both access points have to be on the same LAN IP subnet. That is, all the access point

LAN IP addresses are in the same network.

•

All LAN devices (wired and wireless computers) have to be configured to operate in the

same LAN network address range as the access points.

Wireless Repeating Function

Select

Advanced > Advanced Setup > Wireless Repeating Function

to view or change

wireless repeater settings for the wireless modem router.

•

Enable Wireless Repeating Function

. Select the check box for the 2.4 GHz or 5 GHz

network to use the wireless repeating function.