Onkyo TX-NR3010 Owner Manual

Onkyo TX-NR3010 Manual

Get Onkyo TX-NR3010 PDF manuals and user guides View all Onkyo TX-NR3010 manuals
Add to My Manuals
Save this manual to your list of manuals

Onkyo TX-NR3010 manual content summary:

  • Onkyo TX-NR3010 | Owner Manual - Page 1
    AV RECEIVER TX-NR5010 TX-NR3010 Instruction Manual Contents Safety Information and Introduction 2 Table of Contents 6 Connections 13 Turning On & Basic Operations 26 Advanced Operations 57 Controlling Other Components 92 Appendix 101 Internet Radio Guide Remote Control Codes En
  • Onkyo TX-NR3010 | Owner Manual - Page 2
    equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all
  • Onkyo TX-NR3010 | Owner Manual - Page 3
    sound by your Onkyo dealer. 8. user's authority to operate the equipment. NOTE: This equipment has been tested instructions receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver
  • Onkyo TX-NR3010 | Owner Manual - Page 4
    DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. Sur les modèles dont la fiche est polarisée: ATTENTION: cord of this unit should be performed only by qualified service personnel. IMPORTANT The wires in the mains lead are coloured the ONKYO product described in this instruction manual is
  • Onkyo TX-NR3010 | Owner Manual - Page 5
    , as shown below. Remote control sensor AV receiver Approx. 16 ft. (5 m) Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and
  • Onkyo TX-NR3010 | Owner Manual - Page 6
    Network Service Troubleshooting 101 Firmware Update 107 Connection Tips and Video Signal Path 111 Using an RIHD-compatible TV, Player, or Recorder 115 About HDMI 117 Network/USB Features 118 License and Trademark Information 121 Specifications 122 To reset the AV receiver to its factory
  • Onkyo TX-NR3010 | Owner Manual - Page 7
    Technology • Digital Processing Crossover Network • DSD Direct for Super Audio CD Connections • 9 HDMI Inputs (1 on front panel) and 2 Outputs • Zone 2 HDMI Output • Onkyo Q for System Control • (TX-NR5010) 7 Digital Inputs (4 Optical/3 Coaxial) • (TX-NR3010) 6 Digital Inputs (3 Optical/3 Coaxial
  • Onkyo TX-NR3010 | Owner Manual - Page 8
    Front & Rear Panels Front Panel B C D Safety Information and Introduction EF (North American models) J K G H I L MN O PQR S T U (European models) [ VWX Y Z En-8
  • Onkyo TX-NR3010 | Owner Manual - Page 9
    button (37) R TUNING MODE button (37) S LISTENING MODE buttons (45) T WHOLE HOUSE MODE button (55) U SETUP MIC jack (43) V SETUP button (61) W HOME button (53) X RETURN button Y USB port (22) Z AUX INPUT jacks (21, 22) [ RT/PTY/TP button (European models) (40) Safety Information and Introduction
  • Onkyo TX-NR3010 | Owner Manual - Page 10
    E F G H L MN O For detailed information, see the pages in parentheses. B Speaker/channel indicators C Z2 (Zone 2) indicator (89) D A and B speaker indicators (15) E (37) FM STEREO indicator (37) K Input indicators (113) HDMI indicator (84) DIGITAL indicator ANALOG indicator L Bi AMP indicator M
  • Onkyo TX-NR3010 | Owner Manual - Page 11
    on TX-NR5010. (North American models) B CD E FGH I JK L M N O Safety Information and Introduction (European models) U P QR S T B RS232 port Terminal for control. C DIGITAL IN COAXIAL and OPTICAL jacks D USB port E ETHERNET port F VREMOTE CONTROL jack G HDMI IN and HDMI output (HDMI OUT
  • Onkyo TX-NR3010 | Owner Manual - Page 12
    54) J DISPLAY button (54) K MUTING button (55) L VOL R/X button (29) M RETURN button N HOME button (53) O SLEEP button (54) Safety Information and Introduction ■ Controlling the tuner To control the AV receiver's tuner, press TUNER (or RECEIVER). You can select AM or FM by pressing TUNER repeatedly
  • Onkyo TX-NR3010 | Owner Manual - Page 13
    subwoofers are recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 42) or manually (➔ page 67). Number of 2 3 4 5 6 7 7 7 8 8 9 9 9 10 11 speakers Front speakers Center speaker Surround
  • Onkyo TX-NR3010 | Owner Manual - Page 14
    PRE OUT of the AV receiver with audio cables. To perform the 11.2-channel playback, set the "11ch " setting is set to "Yes", no sound is output from the FRONT WIDE terminals. Connections outlet before making any connections. • Read the instructions supplied with your speakers. • Pay close attention
  • Onkyo TX-NR3010 | Owner Manual - Page 15
    speaker terminal. Doing so may damage the AV receiver. • Don't connect one speaker to several terminals. About Speakers A and Speakers B Installing Speakers A and Speakers B allows you to enjoy up to 7.2-channel surround-sound playback from each speaker configuration. Each configuration has its
  • Onkyo TX-NR3010 | Owner Manual - Page 16
    speakers In this example, Speakers A provides 5.2-channel surround sound for enjoying DVD movies, while Speakers B is bi-amped for use with a pair of bi-amp capable speakers. Subwoofer 1 is used with Speakers A and Speakers B. Connections ■ 7.2-channel playback with Speakers A or Speakers B The
  • Onkyo TX-NR3010 | Owner Manual - Page 17
    for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on INPUT Powered subwoofer Corner position 1/3 of wall position To find the best position for your subwoofer, while playing a movie or some music
  • Onkyo TX-NR3010 | Owner Manual - Page 18
    are without crossover network by referring to your speaker manual. Connecting speakers without crossover network provide a fine, three-dimensional sound field that extends bass and treble performance to the fullest extent. When speakers without crossover network are used, the AV receiver is able to
  • Onkyo TX-NR3010 | Owner Manual - Page 19
    to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifier. See the manuals supplied with your amplifier for details. L R Power amplifier Note • Specify "None" for any channel that you don't want to output (➔ page 67). • To
  • Onkyo TX-NR3010 | Owner Manual - Page 20
    ray Disc/ DVD player Game console *1 If your TV doesn't support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver. • Before making any AV connections, read the manuals supplied with your AV components. • Don't connect the power
  • Onkyo TX-NR3010 | Owner Manual - Page 21
    /digital video recorder, etc. * If your TV doesn't support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver. * When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on
  • Onkyo TX-NR3010 | Owner Manual - Page 22
    Your Components The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver's display when changing settings. "#$ % "& *1 ' ( ) * GND screw Connections Connect your components to the appropriate jacks
  • Onkyo TX-NR3010 | Owner Manual - Page 23
    TV, projector, etc. Personal computer Note *1 TX-NR5010 only. *2 Do not connect the AV receiver's USB port to a USB port on your HDMI outputs. However, if you have assigned the HDMI inputs to the PC input selector, the AV receiver will output signals received from the HDMI inputs instead of signals
  • Onkyo TX-NR3010 | Owner Manual - Page 24
    FM antenna and AM loop antenna. The AV receiver won't pick up any radio signals without any antenna connected, so you must connect position the antenna to achieve the best possible reception. • Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power
  • Onkyo TX-NR3010 | Owner Manual - Page 25
    AV receiver. The other jack is for connecting additional V-capable components. • Connect only Onkyo components to V jacks. Connecting other manufacturer's components may cause a malfunction. • Some components may not support all V functions. Refer to the manuals supplied with your Onkyo components
  • Onkyo TX-NR3010 | Owner Manual - Page 26
    the AV receiver is connected to your home network (➔ page 118). To perform the firmware update, follow the instructions on screen. Use R/X and ENTER on the AV receiver or remote controller to select one of the options. `Update Now: Starts the firmware update. Refer to "Firmware Update" (➔ page 107
  • Onkyo TX-NR3010 | Owner Manual - Page 27
    HDMI OUT MAIN. Selecting the Language for the Onscreen Setup Menus This step determines the language used for the onscreen setup menus. See "Language" in "OSD Setup" (➔ page 83). Tip • Pressing HOME Network Connection Yes No HOME Exit 1 Use R/X on the AV receiver following instructions on screen
  • Onkyo TX-NR3010 | Owner Manual - Page 28
    No: Displays an error report. Follow the troubleshooting instructions and recheck the source. 4 Use R/X to Skip: Skips this step and continues to "Network Connection". 2 When you're finished, select one of For further details, see the instruction manual provided with the wireless adapter (UWF
  • Onkyo TX-NR3010 | Owner Manual - Page 29
    HDMI outputs. If your TV is connected to other video outputs, use the AV receiver 41) • "iPod/iPhone Playback via Onkyo Dock" (➔ page 92) • " Sound Program Edit" (➔ page 75) Turning On & Basic Operations ■ Operating on the AV receiver signal on the current input source and no operation for a specific
  • Onkyo TX-NR3010 | Owner Manual - Page 30
    Controlling Contents of USB or Network Devices Press USB or NET first. I J B K C L D E M F N G O H P Q R B TOP MENU This button displays the top menu for each media or service. C R/X and ENTER These buttons navigate through the menus. F/S This button cycles through pages. PLAYLIST F/S
  • Onkyo TX-NR3010 | Owner Manual - Page 31
    to HDMI outputs. Home menu. 2 Connect the USB cable that comes with the iPod/iPhone to the USB port on the front of the AV receiver receiver remembers the current mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver appears on the AV receiver's display, do not
  • Onkyo TX-NR3010 | Owner Manual - Page 32
    /iPhone model and generation, the displayed items may vary and the support for Extended Mode (Video) is not guaranteed. Standard Mode Control receiver to your home network (➔ page 118). The on-screen information appears only on a TV that is connected to HDMI outputs. The vTuner Internet Radio Service
  • Onkyo TX-NR3010 | Owner Manual - Page 33
    Registering Other Internet Radio You need to connect the AV receiver to your home network (➔ page 118). The on-screen information appears only on a TV that is connected to HDMI outputs. Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the
  • Onkyo TX-NR3010 | Owner Manual - Page 34
    home network (➔ page 118). The on-screen information appears only on a TV that is connected to HDMI outputs. This section explains how to play music files on a computer or media server through the AV receiver (Server Playback). 1 Start your computer or media server. 2 Press NET. The network service
  • Onkyo TX-NR3010 | Owner Manual - Page 35
    connect the AV receiver to your home network (➔ page 118). The on-screen information appears only on a TV that is connected to HDMI outputs. Remote receiver will not be reflected in the "Remote playback" window. Note • Remote playback cannot be used in any of the following cases: - Network services
  • Onkyo TX-NR3010 | Owner Manual - Page 36
    instruction manual provided with your NAS unit. Turning On & Basic Operations Playing music files on a shared folder In order to enjoy Home Media, you must first create a shared folder on your computer. 1 On the remote controller, press RECEIVER followed by NET. The network service the user account
  • Onkyo TX-NR3010 | Owner Manual - Page 37
    get good reception. In this case, switch to manual tuning mode and listen to the station in mono. ■ Manual tuning mode In manual tuning mode, FM stations will be in mono. 1 Press TUNING MODE so that the AUTO indicator goes off on the AV receiver's display. 2 Press and hold TUNING R/X. The frequency
  • Onkyo TX-NR3010 | Owner Manual - Page 38
    of the band and frequency. • When music data is received, song title and artist name information will be displayed next to the "HD" indicator. • If the current HD Radio station supports multicast channels, the currently selected multicast channel will be displayed to the right of the "HD" indicator
  • Onkyo TX-NR3010 | Owner Manual - Page 39
    signal when available. ` Analog: Select to use the analog signal. Note • Multicast channels 2 through 8 are digital only, so you must select multicast channel news, sport, rock, etc.). The AV receiver supports four types of RDS information: PS (Program Service) When tuned to an RDS station that's
  • Onkyo TX-NR3010 | Owner Manual - Page 40
    characters may be displayed when unsupported characters are received. This is not a malfunction. • If the signal from an RDS station is weak, RDS data Country music National music Oldies music Folk music Documentary Alarm test Alarm Display None News Affairs Info Sport Educate Drama Culture
  • Onkyo TX-NR3010 | Owner Manual - Page 41
    is retained. 3 Start playback on your Blu-Ray Disc/DVD and CD players. You can now enjoy watching your Blu-ray Disc/DVD with the sound of your CD player. Turning On & Basic Operations En-41
  • Onkyo TX-NR3010 | Owner Manual - Page 42
    best listening environment. The Quick Start takes 2 minutes and Full Calibration takes about 20 minutes. Total measurement time varies depending on the number of speakers. Measurement procedure To create a listening environment in your home theater The microphone picks up test tones played through
  • Onkyo TX-NR3010 | Owner Manual - Page 43
    to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver's Network (➔ page 71). Continue with the settings. 4 Adjust the subwoofer volume level to 75 dB, and then press ENTER. Test subwoofer (SW2) will not be measured and no sound will be output. An error will occur if
  • Onkyo TX-NR3010 | Owner Manual - Page 44
    Front High Surround Back Surround Back Ch -- Review Speaker Configuration -- 2ch 40Hz 40Hz 100Hz and Speaker Setup. • If the AV receiver is muted, it will be unmuted automatically this message appears after 2 or 3 attempts, contact your Onkyo dealer. • Speaker Detect Error This message appears if
  • Onkyo TX-NR3010 | Owner Manual - Page 45
    to Off or Direct. Refer to your subwoofer's instruction manual for details. Using the Listening Modes Selecting Listening Modes See "About Listening Modes" for detailed information about the listening modes (➔ page 46). ■ Listening Mode Buttons Press RECEIVER first. MUSIC MOVIE/TV GAME THX PURE
  • Onkyo TX-NR3010 | Owner Manual - Page 46
    Source The following audio formats are supported by the listening modes. " 4 % ' ( ) This is mono (monophonic) sound. This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers. This is 5.1-channel surround sound. This surround system has five
  • Onkyo TX-NR3010 | Owner Manual - Page 47
    N*1 ^ W*2 *1 After enabling the corresponding speakers, press RECEIVER followed by SP (speaker layout) repeatedly to select the speakers power amplifier is connected to FRONT WIDE PRE OUT of the AV receiver and the "11ch Playback" setting is set to "Yes" (➔ page 14, 66). En-47 Turning
  • Onkyo TX-NR3010 | Owner Manual - Page 48
    ■ Onkyo-Original DSP Listening Modes Listening Mode Orchestra Or ches t r a Unplugged operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and and sound localization decreased slightly. Turning On & Basic Operations Listening Mode All Ch Stereo A l l Ch
  • Onkyo TX-NR3010 | Owner Manual - Page 49
    signals input through HDMI IN can be output from the HDMI output.) " 4 % ' ( ) [YD O*2N W In this mode, audio from the input source is output without surround-sound it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or
  • Onkyo TX-NR3010 | Owner Manual - Page 50
    Mo v i e PL Mu s i c PL Game PL x Mo v i e PL x Mu s i c PL x Game Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener. As well as music and movies, video games can also benefit
  • Onkyo TX-NR3010 | Owner Manual - Page 51
    stringent standards that ensure movies are reproduced in movie theaters and home theaters just as the director intended. THX Modes carefully Games modes can be used. The PLII/PLIIx and THX indicators light on the AV receiver's display. DON W • Dolby Pro Logic IIx Movie + THX % Cinema ) •
  • Onkyo TX-NR3010 | Owner Manual - Page 52
    , the listening mode will automatically switch to Direct. *2 Based on the audio channel signal contained in the source, the corresponding speakers will output the sound. *3 The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the output on the player side to
  • Onkyo TX-NR3010 | Owner Manual - Page 53
    HOME on the AV receiver. 2 Use F/S or R/X and ENTER to make the desired selection. Press HOME to close the menu. ■ Network Service You need to connect the AV receiver to your home network page 57). ■ Firmware Update `With this selection, you can update the firmware of the AV receiver. Note that this
  • Onkyo TX-NR3010 | Owner Manual - Page 54
    , you can use DISPLAY on the AV receiver. The following information can be typically displayed. Input source Listening mode Signal format*1 Sampling frequency Input signal resolution Output resolution *1 If the input signal is digital, the signal format is displayed. Information is displayed for
  • Onkyo TX-NR3010 | Owner Manual - Page 55
    music to your home party; this Network is used (➔ page 71). Selecting Speaker Layout You can set which speakers you want to use by priority. 1 Press RECEIVER followed by SP (speaker layout) repeatedly to select: ■ 9.2 ch When a listening mode which doesn't support front high, front wide or surround
  • Onkyo TX-NR3010 | Owner Manual - Page 56
    sound will be output from the headphones jack. Using Easy Macros By using ACTIVITIES in Easy macro mode, you can sequentially operate Onkyo components via simple commands from a single-button press. These commands are user -ray Disc/DVD player, the AV receiver may not activate this playback command.
  • Onkyo TX-NR3010 | Owner Manual - Page 57
    Setup menu (HOME) provides a convenient way to change the AV receiver's various settings. Settings are organized into 9 categories. The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver's display when changing
  • Onkyo TX-NR3010 | Owner Manual - Page 58
    HDMI IN 5/6/7/8 is the current HDMI input source, or - No signal is present on the current input source, or - The "Zone 2 HDMI and listening mode, not all channels shown here output the sound. *7 • This setting is not is selected. Operating on the AV receiver 1 Press TONE repeatedly to select either
  • Onkyo TX-NR3010 | Owner Manual - Page 59
    You cannot use these function while the AV receiver is muted. • These settings cannot be used while a pair of headphones is connected. • Speakers that are set to "No" or "None" in "Speaker Configuration" (➔ page 67) cannot be adjusted. • When "Sound Program" is enabled, "Subwoofer 1" and "Subwoofer
  • Onkyo TX-NR3010 | Owner Manual - Page 60
    Program" is enabled, the setting must be made with "Sound Program Edit" (➔ page 75). Re-EQ With the Re-EQ function, you can compensate a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. ■ Re-EQ ` Off ` On This function can be used with the
  • Onkyo TX-NR3010 | Owner Manual - Page 61
    setting. Press HOME to close the menu. Press RETURN to return to the previous menu. Note • This procedure can also be performed on the AV receiver by using the AV receiver's display. ■ Screen Saver If there is no video signal on the current input source and no operation for a specific time (three
  • Onkyo TX-NR3010 | Owner Manual - Page 62
    Monitor Out HDMI Input Component Video Input Digital Audio Input Speaker Settings Speaker Configuration Speaker Distance Level Calibration Equalizer Settings THX Audio Setup Digital Processing Crossover Network Multiplex/Mono Dolby DTS Audyssey DSX Theater-Dimensional LFE Level Direct Sound Program
  • Onkyo TX-NR3010 | Owner Manual - Page 63
    . Video signals are output from both HDMI outputs at the resolution supported by both TVs. Changing the "Monitor Out" setting manually 1 Press MONITOR OUT on the front panel. The current setting is displayed. 2 Press MONITOR OUT on the AV receiver repeatedly to select: ` Analog, HDMI Main, HDMI Sub
  • Onkyo TX-NR3010 | Owner Manual - Page 64
    and COMPONENT VIDEO MONITOR OUT so that the AV receiver upconverts the picture resolution as necessary to match the resolution supported by your TV. Tip • You can see the picture by pressing ENTER to check the "Resolution" setting for HDMI OUT MAIN (excluding NET input source). Note • Depending on
  • Onkyo TX-NR3010 | Owner Manual - Page 65
    PHONO (TX-NR5010) `COAXIAL1, COAXIAL2, COAXIAL3, OPTICAL1, OPTICAL2, OPTICAL3: (TX-NR3010) `COAXIAL1, COAXIAL2, COAXIAL3, OPTICAL1, OPTICAL2: Select the input to which the component has been connected. `- - - - -: Select if the component is connected to an analog audio input. Note • When an HDMI IN
  • Onkyo TX-NR3010 | Owner Manual - Page 66
    manually. ). - "HDMI Control(RIHD Network" (➔ page 18). Note • When bi-amping is used, the AV receiver Network (➔ page 71). Continue with the settings. ■ Powered Zone 2, Powered Zone 3 ` No ` Yes: Zone 2/3 speakers can be used. (Powered Zone 2/3 enabled). ■ 11ch Playback ` No ` Yes For 11.2-channel
  • Onkyo TX-NR3010 | Owner Manual - Page 67
    Yes". - The "Zone 2 HDMI" setting is set to "Use". • If the "11ch Playback" setting is set to "Yes", the audio of front wide channel is output from FRONT WIDE frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker's manuals to
  • Onkyo TX-NR3010 | Owner Manual - Page 68
    is enabled (➔ page 89), this setting cannot be selected. ■ Surround Back Ch ` 1ch: Select if only one surround back speaker L is connected. ` this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Note • When the "Subwoofer"
  • Onkyo TX-NR3010 | Owner Manual - Page 69
    manually. Here you can adjust the level of each speaker with the built-in test steps. Note • These settings cannot be calibrated when the AV receiver is muted. • Speakers that you set to "No" or 67). Tip • If you're using a handheld sound level meter, adjust the level of each speaker so that
  • Onkyo TX-NR3010 | Owner Manual - Page 70
    Manual Equalizer ` On: You can adjust the equalizer for each speaker manually. Continue with the following procedure: 1 Press X to select "Channel sounds; high frequencies (e.g., 16000 Hz) affect treble sounds. 3 Use R to select "Channel page 67). - "Surround Back Ch" is set to "1ch" the HDMI
  • Onkyo TX-NR3010 | Owner Manual - Page 71
    can be received by your Onkyo AVR and can be sent to other devices that are connected in your home theater system, with be "2500Hz". Tip • Sounds processed by Digital Processing Crossover Network are played. • You can switch from the current audio source to test noises by pressing MODE/D
  • Onkyo TX-NR3010 | Owner Manual - Page 72
    Tip • Sounds processed by Digital Processing Crossover Network are played. • You can switch from the current audio source to test noises by pressing Dolby ■ PL IIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If you're not using any surround back speakers, these settings
  • Onkyo TX-NR3010 | Owner Manual - Page 73
    mix, allowing you to adjust the weight of the center channel sound. ■ PL IIz Height Gain ` Low ` Mid ` High Manual: You can select any available listening mode. This setting determines how Dolby EX encoded signals are or source components, freeing the user from having to make volume adjustments
  • Onkyo TX-NR3010 | Owner Manual - Page 74
    average listening level so the user does not have to change theater where the playback loudness is preset, you can choose your preferred volume setting for best enjoyment. DTS ■ Neo:X Music Center Image ` 0 to 2 to 5 The DTS Neo:X Music listening mode creates 9-channel surround sound from 2-channel
  • Onkyo TX-NR3010 | Owner Manual - Page 75
    Frequency Effects) channel individually for signals are passed through the DSP for A/V Sync, delay, etc., processing when the Pure Audio or Direct listening mode is selected. Note • When Digital Processing Crossover Network is being used, this setting is not available. Sound Program Edit ■ Sound
  • Onkyo TX-NR3010 | Owner Manual - Page 76
    speaker level must be adjusted so that -30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home theater system automatically calibrated by Audyssey MultEQ® XT32 will play at reference level when the master volume control is set to the
  • Onkyo TX-NR3010 | Owner Manual - Page 77
    EQ® Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is
  • Onkyo TX-NR3010 | Owner Manual - Page 78
    Picture Mode*1*3 ` Custom: All settings can be performed manually. `ISF Day: Select when the room is bright. from an analog input and output by the HDMI output is processed in the same way : According to the input signals and monitor output setting, the AV receiver automatically selects the "4:3", "
  • Onkyo TX-NR3010 | Owner Manual - Page 79
    per second. `4K Upscaling: Select this for an output resolution four times that of 1080p. Depending on the resolution supported by your TV, it will result in either 3840 × 2160 or 4096 × 2160 pixels. You can specify the output resolution for the HDMI output and have the AV receiver upconvert the
  • Onkyo TX-NR3010 | Owner Manual - Page 80
    " setting is set to "4K Upscaling" (➔ pages 63, 79), this setting is fixed at "Off". *6 Press CLR if you want to reset to the default value. *7 ` ARC: The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver.*1 With this selection, the Channel" setting (➔ page 84). En-80
  • Onkyo TX-NR3010 | Owner Manual - Page 81
    the dts indicator will flash and there will be no sound. When "HDMI", "COAXIAL" or "OPTICAL" is selected in the "Audio Selector" setting, you can then specify the signal type in "Fixed Mode". Normally, the AV receiver detects the signal format automatically. However, if you experience either of the
  • Onkyo TX-NR3010 | Owner Manual - Page 82
    digital audio signals are played (DVD, etc.). Specifies the default listening mode for Dolby TrueHD sources, such as Blu-ray or HD DVD (input via HDMI). ■ to be used each time the AV receiver is turned on. To use the same volume level that was used when the AV receiver was turned off, select "Last".
  • Onkyo TX-NR3010 | Owner Manual - Page 83
    go off and the screen will return to its previous state if the AV receiver is operated in any way. Hardware Setup 1 2 3 4 5 "Setup the setting to "Off". • Refer to the connected component's instruction manual for details. • When the "HDMI Control(RIHD)" setting is set to "On", the power
  • Onkyo TX-NR3010 | Owner Manual - Page 84
    of the "HDMI Control(RIHD)", "HDMI Through" or "Audio Return Channel", turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user's manuals for all connected pieces of equipment. ■ Lip Sync ` Off ` On This function allows the AV receiver to automatically
  • Onkyo TX-NR3010 | Owner Manual - Page 85
    Home menu (➔ page 53) and specify the preview display of HDMI video signals, the Network After modifying the network settings, you must confirm the changes by executing "Save". This section explains how to configure the AV receiver's network settings manually by your Internet Service Provider (ISP).
  • Onkyo TX-NR3010 | Owner Manual - Page 86
    mode. ■ Update Notice ` Enable ` Disable When this setting is enabled, you will be notified if a firmware update via network is available. 2, or 3 When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from other components, you
  • Onkyo TX-NR3010 | Owner Manual - Page 87
    When Powered Zone 2 is used, playback in the main room is reduced to 7.2 channels. • When Powered Zone 3 is used, playback in the main room is reduced to 5.2 channels. Connecting Your Zone Speakers Directly to the AV receiver This setup allows you to select different sources for Main room and Zone
  • Onkyo TX-NR3010 | Owner Manual - Page 88
    9.2-channel playback in your main listening room and 2-channel receiver turns on or off the Zone 2/3. Zone 2 Video Output Advanced Operations Note • If you use HDMI OUT ZONE 2, make sure to set "Zone 2 HDMI" to "Use" (➔ page 63). • Video and audio signals from an HDMI input will be output to HDMI
  • Onkyo TX-NR3010 | Owner Manual - Page 89
    , press ZONE 2 or ZONE 3 followed by an input selector button within 8 seconds. Zone 2/3 turns on, the Z2 or Z3 indicator lights on the AV receiver's display. Tip • The corresponding trigger output goes high (+12 V). To select AM or FM, press ZONE 2 or ZONE 3 and the TUNER input selector repeatedly
  • Onkyo TX-NR3010 | Owner Manual - Page 90
    same input source, only an analog input signal is output. • If an HDMI component selected in Zone 2 outputs the sound other than PCM, the sound is not output from FRONT WIDE/ZONE 2 in Zone and Multiroom Control Kits To control the AV receiver with the remote controller while you're in Zone, you
  • Onkyo TX-NR3010 | Owner Manual - Page 91
    jack and placed in front of the other component's remote control sensor. Infrared signals received at the AV receiver's IR IN jack are fed through to the other component via the IR emitter. Signals picked up by the AV receiver's remote control sensor are not output. IR IN IR OUT Connecting block
  • Onkyo TX-NR3010 | Owner Manual - Page 92
    information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site. For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock. RI
  • Onkyo TX-NR3010 | Owner Manual - Page 93
    the remote control code 81993 (with V). • Set the AV receiver's Input Display to "DOCK" (➔ page 54). ■ Without detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock. *1 TOP MENU works as seconds. *3 This button does not turn the Onkyo DS-A2 or DS-A2X RI Dock on or
  • Onkyo TX-NR3010 | Owner Manual - Page 94
    Onkyo CD player (➔ page 96) STB/DVR Apple TV Looking up for Remote Control Codes You can look up for an appropriate remote control code from the on-screen menu. You need to connect your TV to the HDMI output (HDMI OUT MAIN) to make the following on-screen setting. 1 Press RECEIVER followed by HOME
  • Onkyo TX-NR3010 | Owner Manual - Page 95
    MODE buttons to their default settings, see "Resetting the REMOTE MODE Buttons" (➔ page 96). Note • If any other button than the colored buttons is pressed, the operation will be cancelled. • This operation cannot be done while the AV receiver is in Receiver mode or when ZONE 2/3 is active. En
  • Onkyo TX-NR3010 | Owner Manual - Page 96
    learning command is also reset. Resetting the Remote Controller You can reset the remote controller to its default settings. 1 While holding down RECEIVER, press and hold down HOME until RECEIVER lights (about 3 seconds). 2 Within 30 seconds, press RECEIVER again. RECEIVER flashes twice, indicating
  • Onkyo TX-NR3010 | Owner Manual - Page 97
    player with Q *1 The Q supported by the AV receiver is the CEC system control function of the HDMI standard. Press the appropriate REMOTE GUIDE D R/X/F/S ENTER E SETUP F , *1 G A (Red)*1 B (Green)*1 C (Yellow)*1 D (Blue)*1 H Number: 1 to 9, 0 Number: +10*1 I DISPLAY K MUTING L CH +/- M PREV CH
  • Onkyo TX-NR3010 | Owner Manual - Page 98
    expected, and some may not work at all. • See "Controlling Your iPod/iPhone" about the operation of iPod/iPhone (➔ page 93). *1 The Q function is not supported. The Q supported by the AV receiver is the CEC system control function of the HDMI standard.
  • Onkyo TX-NR3010 | Owner Manual - Page 99
    CH MOSDUER C D SLEEP POWER VIDEO-2 DVGDTRAOPUEPINPTUUTTNSUEPENRLREEERCSPTEDITHOMRONMEOR DV D VIDEO-1 C D TOTNEEST DISC CH command, press and hold down RECEIVER until the REMOTE MODE button lights with commands for controlling Onkyo CD players, cassette any time by resetting the remote
  • Onkyo TX-NR3010 | Owner Manual - Page 100
    they were programmed. Keep the remote controller pointed at the AV receiver until all of the commands have been transmitted. Macros can be run at any time, regardless of the current remote controller mode. Deleting Macros 1 While holding down HOME, press and hold down ALL OFF until ALL OFF lights
  • Onkyo TX-NR3010 | Owner Manual - Page 101
    settings. RECEIVER HOME To reset the remote controller to its factory defaults, while holding down RECEIVER, press and hold down HOME until RECEIVER lights (about 3 seconds). Within 30 seconds, press RECEIVER again. The on-screen information appears only on a TV that is connected to HDMI outputs
  • Onkyo TX-NR3010 | Owner Manual - Page 102
    produce no sound When the T-D (Theater-Dimensional), Stereo or - Mono listening mode is selected, the surround speakers produce no sound. Depending channel, the subwoofer produces no sound. Make sure the speakers are configured correctly. 67 ■ There's no sound with a certain signal format
  • Onkyo TX-NR3010 | Owner Manual - Page 103
    is not a malfunction. ■ The beginning of audio received by an HDMI IN can't be heard Since it takes longer to identify the format of an - HDMI signal than it does for other digital audio signals, audio output may not start immediately. ■ There's no sound during Whole House Mode Make sure you
  • Onkyo TX-NR3010 | Owner Manual - Page 104
    no sound Make sure your iPod/iPhone is actually playing. - Make sure your iPod/iPhone is properly inserted in - the Dock. Make sure the AV receiver is turned on, the correct - input source is selected, and the volume is turned up. Make sure the plugs are pushed in all the way. - Try resetting
  • Onkyo TX-NR3010 | Owner Manual - Page 105
    status, the AV receiver will enter standby mode as usual.) - The "HDMI Through" setting is set to other than "Off". - The "Network Standby" setting The values entered may be automatically adjusted - with values best-suited for your home theater. ■ The display doesn't work The display is turned
  • Onkyo TX-NR3010 | Owner Manual - Page 106
    . Check if the unit produces normal sounds. ■ The following settings can be your TV/monitor connected to the HDMI output is unstable, try switching receiver's display and release the buttons. The AV receiver contains a microcomputer for signal plug it back in. Onkyo is not responsible for damages
  • Onkyo TX-NR3010 | Owner Manual - Page 107
    , or for any other reason whatsoever. See the Onkyo web site for latest information. Appendix Updating the Firmware via Network The AV receiver allows you to update the firmware using network connection on the rear panel. Note • Make sure your AV receiver and TV are turned on and an Ethernet cable
  • Onkyo TX-NR3010 | Owner Manual - Page 108
    router is configured properly. See the instruction manual of the router. • If your network allows only one client connection and there is any other device already connected, the AV receiver will not be able to access the network. Consult your Internet Service Provider (ISP). • If your modem does
  • Onkyo TX-NR3010 | Owner Manual - Page 109
    up to 60 minutes to complete the firmware update. • The AV receiver will retain all your settings after the update is finished. Before Starting • Set the "HDMI Control(RIHD)" setting to "Off" (➔ page 83). • Turn off the controller device connected via RS232 and network. • Turn off Multi Zone if this
  • Onkyo TX-NR3010 | Owner Manual - Page 110
    of the USB device, or the firmware file is for another model. Retry and download the file on the support page of the web site, following the on-site instructions. If the error persists, please contact Onkyo Support and provide the error code. Retry the update procedure from the beginning. If the
  • Onkyo TX-NR3010 | Owner Manual - Page 111
    video, or HDMI, the latter offering the best picture quality. The AV receiver can upconvert between HDMI outputs. Use this setting if you connect both HDMI OUT MAIN and HDMI OUT SUB of the AV receiver to your TV. Note that video signals are output from both HDMI outputs at the resolution supported
  • Onkyo TX-NR3010 | Owner Manual - Page 112
    , refer to "Video Resolution Chart" (➔ page 114). Composite PC IN Component (Analog RGB) IN AV receiver Composite MONITOR OUT Component HDMI HDMI TV, projector, etc Appendix ■ Signal Selection If signals are present at more than one input, the inputs will be selected automatically in the
  • Onkyo TX-NR3010 | Owner Manual - Page 113
    of priority: HDMI, digital, analog. Audio Signal Flow Chart Blu-ray Disc/DVD player, etc. Analog AV receiver *1 Optical Coaxial IN *1 *1 HDMI OUT TV, projector, etc. HDMI *1 *2 *1 Depends on the "Audio TV Out" setting (➔ page 84). *2 This is possible when "Audio Return Channel" is set
  • Onkyo TX-NR3010 | Owner Manual - Page 114
    OUT SUB, they may not display properly on some TVs. *4 Supported resolutions for HDMI OUT SUB ("Monitor Out" = "Sub"). *5 Supported resolutions for HDMI OUT SUB ("Monitor Out" = "Both"). *6 The output is limited to 480p/576p for an effective signal in the effect of copy protect. *7 PC IN (Analog RGB
  • Onkyo TX-NR3010 | Owner Manual - Page 115
    the name of the system control function found on Onkyo components. The AV receiver can be used with CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components
  • Onkyo TX-NR3010 | Owner Manual - Page 116
    receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary (➔ page 84). 3. Connect the HDMI the input to which the AV receiver is connected. 5. Following the operating instructions of the TV, select "
  • Onkyo TX-NR3010 | Owner Manual - Page 117
    PC are not supported. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there's no sound from a component connected via HDMI, check its setup. Refer to the connected component's instruction manual for details. En
  • Onkyo TX-NR3010 | Owner Manual - Page 118
    modem, and some Internet Service Providers (ISP) require you to use specific routers. Please consult your ISP or computer dealer if you're unsure. ■ CAT5 Ethernet cable Use a shielded CAT5 Ethernet cable (straight-type) to connect the AV receiver to your home network. ■ Internet Access (for Internet
  • Onkyo TX-NR3010 | Owner Manual - Page 119
    drivers or software. Note that not all USB MP3 players support the USB Mass Storage Class standard. Refer to your USB MP3 player's instruction manual for details. • Protected WMA music files on an MP3 player cannot be played. • Onkyo accepts no responsibility whatsoever for the loss or damage to
  • Onkyo TX-NR3010 | Owner Manual - Page 120
    96 kHz and bitrates of between 8 kbps and 320 kbps are supported. ■ FLAC (.flac or .FLAC) FLAC is a file format networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home. The AV receiver
  • Onkyo TX-NR3010 | Owner Manual - Page 121
    soundtracks for home theater playback. iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. "Made for iPod" and "Made for iPhone" mean that an electronic accessory has been designed to connect specifically to
  • Onkyo TX-NR3010 | Owner Manual - Page 122
    Specifications (TX-NR5010) Amplifier Section Rated Output Power All channels: (North American) 145 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.05% (FTC) (European) 9 ch × 220 W at 6 ohms, 1 kHz, 1
  • Onkyo TX-NR3010 | Owner Manual - Page 123
    Specifications (TX-NR3010) Amplifier Section Rated Output Power All channels: (North American) 140 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.05% (FTC) (European) 9 ch × 200 W at 6 ohms, 1 kHz, 1
  • Onkyo TX-NR3010 | Owner Manual - Page 124
    Fax: +49-8142-4208-213 http://www.eu.onkyo.com/ The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44-(0) 52130396 http://www.cn.onkyo.com/ SN 29401289EN (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. Y1204-1 *
  • Onkyo TX-NR3010 | Owner Manual - Page 125
    network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the desired service and press ENTER. The top page of the selected service appears. Using Multiple Accounts The AV receiver supports multiple user
  • Onkyo TX-NR3010 | Owner Manual - Page 126
    radio service that plays instructions to create your Pandora account and your personalized Pandora Internet radio stations. You can create your stations by entering your favorite songs and artists when prompted. After you have created your account and stations you can return to your Onkyo receiver
  • Onkyo TX-NR3010 | Owner Manual - Page 127
    www.rhapsody.com/onkyo If you have an existing Rhapsody account, select "Sign in to your account" and press ENTER. Enter your user name (usually your Guide: You can play tracks from Genres, Top Artists, Top Albums, Top Tracks, New Releases, and Staff Picks. Rhapsody Channels: Listen to radio channels
  • Onkyo TX-NR3010 | Owner Manual - Page 128
    Onkyo AV receiver includes a free trial of SiriusXM Internet Radio. The "Account Info" screen shows how many days are left in your trial. After the trial period expires, if you want to continue listening to the service Add to My Favorites: Adds a channel to My Favorites list. Using Internet Radio
  • Onkyo TX-NR3010 | Owner Manual - Page 129
    With thousands of biographies, reviews and an endless choice of best of ad-free Last.fm Radio on your Onkyo AV receiver at your fingertips. Latest prices and full information are available the ENTER to enter your user name and password. 2. Select services provided by a third party may be
  • Onkyo TX-NR3010 | Owner Manual - Page 130
    Sign In" and press ENTER to use a restricted version of the service. Note that use will be restricted. Tip • If you want to use multiple user accounts, see "Using Multiple Accounts" (➔ page 1). Login can be made from the "Users" screen. 4 Use R/X to select a menu item and then press ENTER. To
  • Onkyo TX-NR3010 | Owner Manual - Page 131
    home AV Receiver Tip • Before proceeding, you need to select the MP3tunes service Users" screen. 4 Use R/X to select the menu, then press ENTER. Music: The place to find your Artists, Albums, and Playlists. Shuffle: Starts playing a random selection of tracks from your Locker. Search: Find a specific
  • Onkyo TX-NR3010 | Owner Manual - Page 132
    est affiché. Les éléments de menu suivants s'affichent : Add new user : Remove this user : Vous pouvez soit stocker un nouveau compte utilisateur, soit en supprimer un existant. Conseil • Certains des services ne permettent pas l'utilisation de plusieurs comptes utilisateur. • Vous pouvez stocker
  • Onkyo TX-NR3010 | Owner Manual - Page 133
    tats-Unis uniquement) Pandora est un service de radio en ligne libre et navigateur à www.pandora.com/onkyo Saisissez votre code d'activation puis suivez les instructions pour créer votre compte Pandora peut être réalisée à partir de l'écran « Users ». 2 Pour lire une station, utilisez R/X pour sé
  • Onkyo TX-NR3010 | Owner Manual - Page 134
    créer un à partir de www.rhapsody.com/onkyo Si vous possédez déjà un compte Rhapsody, partir de l'écran « Users ». 2 Utilisez R/X pour par album ou par piste. Music Guide : Vous pouvez lire des pistes de lecture en cours de lecture. Add channel to My Channels : Marquez les canaux de radio Rhapsody
  • Onkyo TX-NR3010 | Owner Manual - Page 135
    Onkyo comprend un essai gratuit de SiriusXM Internet Radio. L'écran « Account Info » affiche le nombre de jours restants dans votre essai. Une fois la période d'essai expirée, si vous souhaitez continuer à écouter le service réalisée à partir de l'écran « Users ». ■ Utilisation de l'écran clavier 1.
  • Onkyo TX-NR3010 | Owner Manual - Page 136
    la webradio Last.fm Last.fm un service de musique qui apprend ce que vous aimez... Votre nouvel ampli-tuner AV Onkyo est très intelligent. Si vous avez page 1). L'identification peut être réalisée à partir de l'écran « Users ». 2 Utilisez R/X pour sélectionner un menu puis appuyez sur ENTER. Search
  • Onkyo TX-NR3010 | Owner Manual - Page 137
    In », puis appuyez sur ENTER pour utiliser une version restreinte du service. Veuillez noter que l'utilisation est restreinte. Conseil • Si vous souhaitez page 1). L'identification peut être réalisée à partir de l'écran « Users ». 4 Utilisez R/X pour sélectionner un élément du menu, puis appuyez sur
  • Onkyo TX-NR3010 | Owner Manual - Page 138
    guardar hasta 10 cuentas de usuario. • Para cambiar entre cuentas debe antes cerrar sesión en la cuenta actual y acceder de nuevo en la pantalla "Users". Uso de Internet Radio Pandora® Internet Radio -Primeros pasos (solo EE.UU 2 Uso de Rhapsody (sólo EE.UU 3 Uso de SiriusXM Internet Radio (solo
  • Onkyo TX-NR3010 | Owner Manual - Page 139
    ordenador conectado a Internet y dirija el navegador a www.pandora.com/onkyo Introduzca su código de activación y siga las instrucciones para crear su cuentas" (➔ página 1). Se puede iniciar sesión desde la pantalla "Users". 2 Utilice R/X para seleccionar la emisora en la lista de emisoras y
  • Onkyo TX-NR3010 | Owner Manual - Page 140
    una nueva en www.rhapsody.com/onkyo Si ya tiene una cuenta iniciar sesión desde la pantalla "Users". 2 Utilice R/X para seleccionar el Guide: Puede reproducir canciones por géneros, artistas principales, álbumes principales o canciones principales, novedades, selección del sitio. Rhapsody Channels
  • Onkyo TX-NR3010 | Owner Manual - Page 141
    Radio (solo Norteamérica) Su receptor de AV Onkyo incluye una prueba gratuita de SiriusXM Internet Radio. La "Uso de múltiples cuentas" (➔ página 1). Se puede iniciar sesión desde la pantalla "Users". ■ Utilización de la pantalla de teclado 1. Utilice R/X/F/S y ENTER para introducir su nombre
  • Onkyo TX-NR3010 | Owner Manual - Page 142
    mejor de Last.fm Radio sin anuncios en su receptor de AV Onkyo sin necesidad de un ordenador. Recommended Radio: Descubra nuestras interesantes recomendaciones cuentas" (➔ página 1). Se puede iniciar sesión desde la pantalla "Users". 2 Utilice R/X para seleccionar un menú y luego pulse ENTER. Search
  • Onkyo TX-NR3010 | Owner Manual - Page 143
    • Si desea utilizar múltiples cuentas de usuario, consulte "Uso de múltiples cuentas" (➔ página 1). Se puede iniciar sesión desde la pantalla "Users". 4 Utilice R/X para seleccionar un menú y luego pulse ENTER. Para salir, utilice R/X para seleccionar "Sign out" en esta pantalla y luego pulse
  • Onkyo TX-NR3010 | Owner Manual - Page 144
    SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. Y1203-2 * 2 9 4 0 1 1 8 9 B *
  • Onkyo TX-NR3010 | Owner Manual - Page 145
    network services appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the desired service and press ENTER. The top page of the selected service appears. Using Multiple Accounts The AV receiver supports multiple user
  • Onkyo TX-NR3010 | Owner Manual - Page 146
    reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join UK and Germany only: Get a subscription and you can enjoy the best of ad-free Last.fm Radio on your Onkyo AV receiver prices user
  • Onkyo TX-NR3010 | Owner Manual - Page 147
    Die oberste Seite des ausgewählten Services erscheint. Verwendung mehrerer Konten Der AV-Receiver unterstützt mehrere Nutzerkonten, was bedeutet, dass Sie frei zwischen mehreren Logins umschalten können. Nach der Anmeldung der Nutzerkonten wird das Login vom „Users" Bildschirm aus vorgenommen. 1 Dr
  • Onkyo TX-NR3010 | Owner Manual - Page 148
    .fm-Radiosender auf Ihrem Onkyo AV-Receiver hören! Recommended Radio: (➔ Seite 1). Das Login kann vom „Users"Bildschirm aus erfolgen. 2 Verwenden Sie R/X, um „Neighbours" wiedergeben. Account Info: Bestätigen Sie Ihre Kontoinformation. Sign (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights
  • Onkyo TX-NR3010 | Owner Manual - Page 149
    button/Remote indicator will flash once slowly. Notes: • The flashing element of the remote controller will differ according to your AV receiver's model. • The remote controller is preconfigured with remote controller presets of different components. By entering a code from the Remote Control Code
  • Onkyo TX-NR3010 | Owner Manual - Page 150
    aparecen con mayúsculas. Por ejemplo, el botón "Remote Mode" y el botón "Display". Notas: • No podrán introducirse códigos de mando a distancia para [RECEIVER] y el botón multizona. • Únicamente podrán introducirse códigos de mando a distancia de televisor para el botón [TV]. • Con la excepción de
  • Onkyo TX-NR3010 | Owner Manual - Page 151
    ] und der Multi-Zonen-Taste zugeordnet werden. • Der Taste [TV] können nur Fernbedienungscodes für einen Fernseher zugeordnet werden. • Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, können die Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden. Allerdings dienen
  • Onkyo TX-NR3010 | Owner Manual - Page 152
    /fjärrindikatorn långsamt en gång. Anmärkningar: • Det blinkande elementet på fjärrkontrollen skiljer sig åt beroende på din modell av AV-receiver. • Fjärrkontrollen har förkonfigurerats med förvalda kanaler på fjärrkontrollen för olika komponenter. Genom att ange en kod från fjärrkontrollkodlistan
  • Onkyo TX-NR3010 | Owner Manual - Page 153
    05&.0 f d3&.05&.0 f ‫ء‬จj 7 d f f d f d d f d f d d f d f d f 遥控代码 Remote Control Codes 1 REMOTE MODE DISPLAY 3 REMOTE MODE Integra Remote Mode Display RECEIVER TV RECEIVER TV REMOTE MODE REMOTE MODE CD CD TV/CD （电视 /CD）]。 2 在 30 5 REMOTE MODE REMOTE MODE
  • Onkyo TX-NR3010 | Owner Manual - Page 154
    Dedicated Onkyo Receiver Default 62503 Zone 2 62506 Zone 3 62507 Cable Set Top Box ADB 02254, 02769 Aon 02769 Arris 02187 AT&T 00858 Bright House 01376, 01877 BT Vision
  • Onkyo TX-NR3010 | Owner Manual - Page 155
    Frontiers Sony Sylvania TAG McLaren Tandy Technics Thorens Thule Audio Traxdata Universum Victor Wards Yamaha Zonda CD-R Denon JVC Kenwood Marantz Onkyo Philips Sony MD Onkyo Sony 7 70157 70157 70157 70157 70157 70157 70157 70036 70157 70157 70490, 70000 70157 70157 70032 70029, 70303 70157 70157
  • Onkyo TX-NR3010 | Owner Manual - Page 156
    02657 02294 00858, 02345 03107 01998, 02802 01385 02345 02769 02378 Receiver Onkyo 52503 Satellite Set Top Box @sat 01300 @Sky 01334 Acoustic Solutions 01100, 01631 Digiwave 01631 DirecTV 01377, 00099 Dish Network 00775 Dishpro 00775 DishTV 01300 DRE 01176 Dream Multimedia
  • Onkyo TX-NR3010 | Owner Manual - Page 157
    Satellite Set Top Box Hama 01567 Hanseatic 01100 Hirschmann 00173 Hitachi 01284 Hornet 01300 HTS 00775 Humax 01377, 01176, 01427, 01675, 01808, 01882, 01915, 02144, 02408, 02616 ID Digital 01176 ID Sat 01334 ILLUSION sat 01631 Imperial 01195, 01334 Indovision 00887 iNETBOX
  • Onkyo TX-NR3010 | Owner Manual - Page 158
    Canal Satellite 02657 Canal+ 02657 CanalSat 02657 Cyfrowy Polsat 02527 Digifusion 01645 DigiQuest 01300 DirecTV 01377, 00099, 20739 Dish Network 00775 Dishpro 00775 Dream Multimedia 01237 Echostar 00775, 02527 Edision 01631 Expressvu 00775 Foxtel 01356 Humax 01176, 01427
  • Onkyo TX-NR3010 | Owner Manual - Page 159
    Television Akai Akiba Akito Akura Alba Alien Allstar Amstrad Anam Anam National Andersson Anitech Ansonic AOC Ardem Arena Aristona ART Art Mito Asberg Astra ATD Atlantic Audiosonic Audiovox Audioworld Aventura Axxon Baird Bang & Olufsen Barco 10178, 10556, 10037, 10714, 10715, 10208, 11675 10037
  • Onkyo TX-NR3010 | Owner Manual - Page 160
    Television Erres ESA ESC Euroman Europa Europhon Evesham Excello Exquisit Ferguson Fidelity Finlandia Finlux Firstline Fisher Flint Formenti Fraba Friac Fujicom Fujitsu Fujitsu Siemens Funai G-Hanz Gaba Galaxi Galaxis Gateway GE GEC 10037 10171 10037 10037 10037 10037 11248, 11667 11037 10037 10037
  • Onkyo TX-NR3010 | Owner Manual - Page 161
    Linsar Local India TV Local Malaysia Metz MGA Micromaxx Microspot Mikomi Minato Minerva Ministry Of Sound Minoka Mirai Mitsubishi Mivar Moree Morgan's Moserbaer MTC MTlogic , 11667 11610, 12124 10698 11667 10653 10714 Television Onix Onkyo Onn Onyx Opera Optimus Orbit Orion Orline Ormond Osaki Osio
  • Onkyo TX-NR3010 | Owner Manual - Page 162
    , 10668, 11037, 12719 10037 Television Sei-Sinudyne Serie Dorada Shanghai Sharp Shintoshi Shivaki Siam Siemens Siera Silva Silva Schneider Silver SilverCrest Sinudyne SKY Skyworth Sliding SLX Solavox Soniko Soniq Sonitron Sonneclair Sonoko Sonolor Sontec Sony Soundesign Soundwave Sowa Squareview
  • Onkyo TX-NR3010 | Owner Manual - Page 163
    Television Technosonic Techvision Techwood Tecnimagen Teco Tedelex Teknika TELE System Telecor Telefunken Telefusion Telegazi Telemeister Telesonic Telestar Teletech Teleview Tennessee Tensai Tesla Tevion Thomson Thorn Thorn-Ferguson TMK Tokai Tokaido Topline Toshiba 10556, 10625, 10499, 11324
  • Onkyo TX-NR3010 | Owner Manual - Page 164
    , 33444 30713 30713 Remote Control Codes DVD Maxim MDS Medion Memorex Metz Micromedia Micromega Microsoft Minax Mitsubishi Momitsu NAD NEC Onkyo Oppo Orion Ormond Pacific Palladium Panasonic Pelican Accessories Philco Philips Pioneer Polk Audio Presidian ProAudio Proscan Proson Pye 30713 30713
  • Onkyo TX-NR3010 | Owner Manual - Page 165
    Anthem Cambridge Audio Denon Dyon Foehn & Hirsch Funai Harman/Kardon Insignia Integra JVC Lenco Lexicon LG Limit Loewe Magnavox Marantz Momitsu Onkyo Oppo Panasonic Philips Pioneer Samsung Sharp Sherwood 30490, 30539, 30646, 30817, 31354, 32298, 32299 30503, 30741 33052 32820 32808 32258, 32748
  • Onkyo TX-NR3010 | Owner Manual - Page 166
    DVD-R Victor Yamaha Zenith 31597 30646 30741 HD-DVD Integra LG Microsoft Onkyo Xbox 32901, 33104 33504 30741 32083 32901, 33104 33504 32083 TV/DVD Combination Akai 11675 Black Diamond 11037, 30713 Blue Sky 11037, 30713 Bush 11037,
  • Onkyo TX-NR3010 | Owner Manual - Page 167
    Memo Remote Control Codes 19
  • Onkyo TX-NR3010 | Owner Manual - Page 168
    SN 29401094 (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. Y1112-1 * 2 9 4 0 1 0 9 4 *
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
E
n
AV RECEIVER
TX-NR5010
TX-NR3010
Instruction Manual
Contents
Safety Information and Introduction
............
2
Table of Contents
...........................................
6
Connections
.................................................
13
Turning On & Basic Operations
..................
26
Advanced Operations
..................................
57
Controlling Other Components
...................
92
Appendix
.....................................................
101
Internet Radio Guide
Remote Control Codes