Onkyo TX-NR3010 Owner Manual - Page 58
Using the Audio Settings of Quick Setup, En-58
View all Onkyo TX-NR3010 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 58 highlights
■ Listening Mode*7 ` You can select the listening modes that are grouped in the following categories: "MOVIE/TV", "MUSIC", "GAME", and "THX". Use R/X to select the category and F/S to select the listening mode. Press ENTER to switch to the selected listening mode. Note *1 • The video preview is not displayed when: - HDMI IN 5/6/7/8 is the current HDMI input source, or - No signal is present on the current input source, or - The "Zone 2 HDMI" setting is set to "Use" (➔ page 63). • The video of the currently-selected input is displayed on the main screen, not on a preview thumbnail. *2 "Dolby Volume", "Dynamic EQ" and "Dynamic Volume" cannot be selected when any of the THX listening modes is selected, with "Loudness Plus" set to "On" or "Preserve THX Settings" set to "Yes" (➔ page 70). *3 When "Dynamic EQ" is set to "On" or "Dynamic Volume" is set to anything else than "Off", "Dolby Volume" will be switched to "Off" (➔ page 73). *4 • When the "Monitor Out" setting is set to "Sub", "Video" cannot be selected (➔ page 63). • This setting cannot be used with the NET input selector. *5 Only when you have selected "Custom" in the "Picture Mode" (➔ page 78), pressing ENTER allows you to adjust the following items via the Quick Setup: "Brightness", "Contrast", "Hue" and "Saturation". Press RETURN to return to the "Picture Mode" setting. *6 Depending on the input source and listening mode, not all channels shown here output the sound. *7 • This setting is not available in either of the following cases: - The "Audio TV Out" setting is set to "On" (➔ page 84). - "HDMI Control(RIHD)" is set to "On" (➔ page 83) and you're listening through your TV speakers. Using the Audio Settings of Quick Setup You can change various audio settings from the Quick Setup (➔ page 57). Note • These settings are not available in either of the following cases: - The "Audio TV Out" setting is set to "On" (➔ page 84). - "HDMI Control(RIHD)" is set to "On" (➔ page 83) and you're listening through your TV speakers. Sound Program ■ Sound Program ` Stereo Source 1, Stereo Source 2, Stereo Source 3, Multich Source 1, Multich Source 2, Multich Source 3 ` Off With this setting, you can select the combination of settings that you registered in "Sound Program Edit" (➔ page 75). Note • If the input selector is changed, the "Sound Program" setting is switched back to "Off". Tone Control Advanced Operations ■ Bass `-10dB to 0dB to +10dB in 2 dB steps. You can boost or cut low-frequency sounds output. ■ Treble `-10dB to 0dB to +10dB in 2 dB steps. You can boost or cut high-frequency sounds output. You can adjust the bass for the front, front wide, front high, center, surround, surround back and subwoofer speakers and treble for the front, front wide, front high, center, surround and surround back speakers, except when the Direct, Pure Audio or THX listening mode is selected. Operating on the AV receiver 1 Press TONE repeatedly to select either "Bass" or "Treble" for each speaker or subwoofer. 2 Use - and + to adjust. Note • Speakers that are set to "No" or "None" in "Speaker Configuration" (➔ page 67) cannot be adjusted. • When "Sound Program" is enabled, "Subwoofer 1" and "Subwoofer 2" cannot be used if the "Subwoofer" setting is set to "No" in "Sound Program Edit" (➔ page 75). En-58