Onkyo TX-NR3010 Owner Manual - Page 95

Entering Remote Control Codes, Remapping Colored Buttons, En-95

Get Onkyo TX-NR3010 PDF manuals and user guides View all Onkyo TX-NR3010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Entering Remote Control Codes You'll need to enter a code for each component that you want to control. 1 Look up the appropriate remote control code in the separate Remote Control Codes list. The codes are organized by category (e.g., DVD player, TV, etc.). 2 While holding down the REMOTE MODE button to which you want to assign a code, press and hold down DISPLAY (about 3 seconds). The REMOTE MODE button lights. Note • Remote control codes cannot be entered for RECEIVER and the multi zone button. • Only TV remote control codes can be entered for TV. • Except for RECEIVER, TV, and the multi zone button, remote control codes from any category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons (➔ page 29), so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose TV/CD when entering its remote control code. 3 Within 30 seconds, use the number buttons to enter the 5-digit remote control code. The REMOTE MODE button flashes twice. If the remote control code is not entered successfully, the REMOTE MODE button will flash once slowly. Note • Though the provided remote control codes are correct at the time of release, they are subject to change. Remapping Colored Buttons You can change the configuration of colored buttons, with which REMOTE MODE buttons are preset. 1 While holding down the REMOTE MODE button that you want to program, press and hold down A (Red) until the REMOTE MODE button lights (about 3 seconds). You can only change colored buttons for components whose codes belong to categories of the Remote Control Codes list (BD/DVD player, TV, cable set-top box, etc). 2 Within 30 seconds, press the colored buttons in the order that you want to reassign them. The button presses are assigned to each button from left to right. The REMOTE MODE button flashes twice, indicating that the sequence has been successfully assigned. If the sequence is not successfully assigned, the REMOTE MODE button will flash once slowly. Tip • To reset the REMOTE MODE buttons to their default settings, see "Resetting the REMOTE MODE Buttons" (➔ page 96). Note • If any other button than the colored buttons is pressed, the operation will be cancelled. • This operation cannot be done while the AV receiver is in Receiver mode or when ZONE 2/3 is active. En-95 Controlling Other Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Controlling Other Components
En-95
You’ll need to enter a code for each component that you
want to control.
Note
•
Though the provided remote control codes are correct at the time
of release, they are subject to change.
You can change the configuration of colored buttons, with
which
REMOTE MODE
buttons are preset.
Tip
•
To reset the
REMOTE MODE
buttons to their default settings,
see “Resetting the REMOTE MODE Buttons” (
➔
page 96
).
Note
•
If any other button than the colored buttons is pressed, the
operation will be cancelled.
•
This operation cannot be done while the AV receiver is in
Receiver mode or when ZONE 2/3 is active.
Entering Remote Control Codes
1
Look up the appropriate remote control code in the
separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
2
While holding down the
REMOTE MODE
button to
which you want to assign a code, press and hold
down
DISPLAY
(about 3 seconds).
The
REMOTE MODE
button lights.
Note
•
Remote control codes cannot be entered for
RECEIVER
and the multi zone button.
•
Only TV remote control codes can be entered for
TV
.
• Except for
RECEIVER
,
TV
, and the multi zone button,
remote control codes from any category can be assigned for
the
REMOTE MODE
buttons. However, these buttons also
work as input selector buttons (
➔
page 29
), so choose a
REMOTE MODE
button that corresponds with the input to
which you connect your component. For example, if you
connect your CD player to the CD input, choose
TV/CD
when entering its remote control code.
3
Within 30 seconds, use the number buttons to enter
the 5-digit remote control code.
The
REMOTE MODE
button flashes twice.
If the remote control code is not entered successfully,
the
REMOTE MODE
button will flash once slowly.
Remapping Colored Buttons
1
While holding down the
REMOTE MODE
button
that you want to program, press and hold down
A
(Red) until the
REMOTE MODE
button lights
(about 3 seconds).
You can only change colored buttons for components
whose codes belong to categories of the Remote
Control Codes list (BD/DVD player, TV, cable set-top
box, etc).
2
Within 30 seconds, press the colored buttons in the
order that you want to reassign them.
The button presses are assigned to each button from
left to right. The
REMOTE MODE
button flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the
REMOTE MODE
button
will flash once slowly.