Onkyo TX-NR708 Owner Manual - Page 70

Setting the Powered Zone 2, Using Zone 2, Controlling Zone 2 from the AV receiver

Get Onkyo TX-NR708 PDF manuals and user guides View all Onkyo TX-NR708 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Setting the Powered Zone 2 Using Zone 2 If you've connected your Zone 2 speakers to the AV receiver, as explained in "Connecting Your Zone 2 Speakers Directly to the AV receiver" (➔ 69), you must set the "Powered Zone2" setting to "Act" (Activated). 1 Press RECEIVER followed by SETUP. The main menu appears onscreen. Tip • If the main menu doesn't appear, make sure the appropri- ate external input is selected on your TV. 2 Use R/X to select "Speaker Setup", and then press ENTER. The "Speaker Setup" menu appears. This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2. Controlling Zone 2 from the AV receiver ZONE 2 indicator OFF 2. Speaker Setup 1. Speaker Settings 2. Speaker Configuration 3. Speaker Distance 4. Level Calibration 5. Equalizer Settings 6. THX Audio Setup 3 Use R/X to select "Speaker Settings", and then press ENTER. The "Speaker Settings" menu appears. 2-1. Speaker Settings Speaker Impedance Speakers Type(Front) Powered Zone2 6ohms Normal Not Act 4 Use R/X to select "Powered Zone2", and use F/S to select: `Not Act: Use FRONT WIDE/ZONE 2 L/R terminals to connect front wide speakers (Powered Zone 2 disabled). ` Act: Use FRONT WIDE/ZONE 2 L/R terminals to connect Zone 2 speakers (Powered Zone 2 enabled). 5 Press SETUP. The setup menu closes. Note • Powered Zone 2 cannot be used if "Speakers Type(Front)" is set to "Bi-Amp" (➔ 45). • This procedure can also be performed on the AV receiver by using SETUP, arrow buttons, and ENTER. Input selector buttons ZONE 2 1 To turn on Zone 2 and select an input source, press ZONE 2 followed by an input selector button within 8 seconds. Zone 2 turns on, the ZONE 2 indicator lights. Tip • ZONE 2 12V TRIGGER OUT goes high (+12 V). To select AM or FM, press TUNER input selector and ZONE 2 repeatedly. (North American models) You can also select SIRIUS. To select the same source as that of the main room, press ZONE 2 twice. "Zone 2 Selector: Source" appears on the display. 2 To turn off Zone 2, press ZONE 2. ZONE 2 indicator flashes. Press OFF. The zone is turned off, and the ZONE 2 indicator goes off. Note • When Zone 2 is turned off, the output from the ZONE 2 12V TRIGGER OUT goes low (0 volts). En 70

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
70
En
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2 Speak-
ers Directly to the AV receiver” (
➔
69
), you must set the
“
Powered Zone2
” setting to “
Act
” (Activated).
Note
•
Powered Zone 2 cannot be used if “
Speakers Type(Front)
” is
set to “
Bi-Amp
” (
➔
45
).
•
This procedure can also be performed on the AV receiver by
using
SETUP
, arrow buttons, and
ENTER
.
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust the
volume for Zone 2.
Controlling Zone 2 from the AV receiver
Note
•
When Zone 2 is turned off, the output from the
ZONE 2 12V
TRIGGER OUT
goes low (0 volts).
Setting the Powered Zone 2
1
Press
RECEIVER
followed by
SETUP
.
The main menu appears onscreen.
Tip
•
If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use
q
/
w
to select “Speaker Setup”, and then press
ENTER
.
The “
Speaker Setup
” menu appears.
3
Use
q
/
w
to select “Speaker Settings”, and then
press
ENTER
.
The “
Speaker Settings
” menu appears.
4
Use
q
/
w
to select “Powered Zone2”, and use
e
/
r
to select:
Not Act
:
Use
FRONT WIDE/ZONE 2 L/R
terminals to
connect front wide speakers (Powered Zone 2
disabled).
Act:
Use
FRONT WIDE/ZONE 2 L/R
terminals to
connect Zone 2 speakers (Powered Zone 2
enabled).
5
Press
SETUP
.
The setup menu closes.
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
2–1. Speaker Settings
Speaker Impedance
Speakers Type(Front)
Powered Zone2
6ohms
Normal
Not Act
Using Zone 2
1
To turn on Zone 2 and select an input source, press
ZONE 2
followed by an input selector button
within 8 seconds.
Zone 2 turns on, the
ZONE 2
indicator lights.
Tip
•
ZONE 2 12V TRIGGER OUT
goes high (+12 V).
To select AM or FM, press
TUNER
input selector
and
ZONE 2
repeatedly.
(North American models)
You can also select SIR-
IUS.
To select the same source as that of the main room,
press
ZONE 2
twice. “
Zone 2 Selector: Source
”
appears on the display.
2
To turn off Zone 2, press
ZONE 2
.
ZONE 2
indicator flashes.
Press
OFF
.
The zone is turned off, and the
ZONE 2
indicator
goes off.
ZONE 2
OFF
ZONE 2
indicator
Input selector buttons