Onkyo TX-NR708 Owner Manual - Page 71

Controlling Zone 2 with the Remote, Controller, Adjusting the Volume for Zone 2, Muting Zone 2

Get Onkyo TX-NR708 PDF manuals and user guides View all Onkyo TX-NR708 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Controlling Zone 2 with the Remote Controller STANDBY ON INPUT SELECTOR ZONE2 Note • To control Zone 2, you must press the remote controller's ZONE2 first. • ZONE2 turns red while Zone 2 is on. 1 Press ZONE2, then point the remote controller at the AV receiver and press ON. Tip • The ZONE 2 12V TRIGGER OUT goes high (+12 V). 2 To select an input source for Zone 2, press ZONE2, followed by INPUT SELECTOR. To select AM or FM, press TUNER input selector and ZONE2 repeatedly. (North American models) You can also select SIRIUS. 3 To turn off Zone 2, press ZONE2, followed by STANDBY. Adjusting the Volume for Zone 2 ■ Operating with the remote controller 1 Press ZONE2. 2 Use VOL R/X to adjust the volume. ■ Operating on the AV receiver 1 Press ZONE 2 (the ZONE 2 indicator and Zone 2 selector on the display flashes). 2 Use -/+ within 8 seconds to adjust the volume. If your Zone 2 speakers are connected to a receiver or integrated amp in Zone 2, use its volume control to adjust the volume. Muting Zone 2 ■ Operating with the remote controller Press ZONE2 followed by MUTING. Tip • To unmute, press ZONE2 followed by MUTING again. Note • Only analog input sources are output by the ZONE 2 LINE OUT and FRONT WIDE/ZONE 2 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, check if it's connected to an analog input. • You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room. For example, if you have an FM station for the main room, that station will also be used in Zone 2. • When you connect Zone 2 speakers directly to the AV receiver, listening modes that require surround back speakers or front high speakers or front wide speakers (6.1/7.1), such as Dolby Digital EX, DTS-ES, THX Select2 Cinema, Dolby Pro Logic IIz Height, and Audyssey DSX™ are unavailable. • When the input selector of Zone 2 is selected, power consumption on standby mode slightly increases. • While Zone 2 is on, V functions will not work. En 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
71
En
Controlling Zone 2 with the Remote
Controller
Note
•
To control Zone 2, you must press the remote controller’s
ZONE2
first.
•
ZONE2
turns red while Zone 2 is on.
Note
•
Only analog input sources are output by the
ZONE 2 LINE
OUT
and
FRONT WIDE/ZONE 2 L/R
terminals. Digital input
sources are not output. If no sound is heard when an input source
is selected, check if it’s connected to an analog input.
•
You cannot select different AM or FM radio stations for your
main room and Zone 2. The same AM/FM radio station will be
heard in each room. For example, if you have an FM station for
the main room, that station will also be used in Zone 2.
•
When you connect Zone 2 speakers directly to the AV receiver,
listening modes that require surround back speakers or front high
speakers or front wide speakers (6.1/7.1), such as Dolby Digital
EX, DTS-ES, THX Select2 Cinema, Dolby Pro Logic IIz
Height, and Audyssey DSX™ are unavailable.
•
When the input selector of Zone 2 is selected, power consump-
tion on standby mode slightly increases.
•
While Zone 2 is on,
u
functions will not work.
Adjusting the Volume for Zone 2
■
Operating with the remote controller
■
Operating on the AV receiver
If your Zone 2 speakers are connected to a receiver or inte-
grated amp in Zone 2, use its volume control to adjust the
volume.
Muting Zone 2
■
Operating with the remote controller
Tip
•
To unmute, press
ZONE2
followed by
MUTING
again.
1
Press
ZONE2
, then point the remote controller at
the AV receiver and press
ON
.
Tip
• The
ZONE 2 12V TRIGGER OUT
goes high (+12 V).
2
To select an input source for Zone 2, press
ZONE2
, followed by
INPUT SELECTOR
.
To select AM or FM, press
TUNER
input selector
and
ZONE2
repeatedly.
(North American models)
You can also select SIR-
IUS.
3
To turn off Zone 2, press
ZONE2
, followed by
STANDBY
.
INPUT
SELECTOR
ON
ZONE2
STANDBY
1
Press
ZONE2
.
2
Use
VOL
q
/
w
to adjust the volume.
1
Press
ZONE 2
(the ZONE 2 indicator and Zone 2
selector on the display flashes).
2
Use
–/+
within 8 seconds to adjust the volume.
Press
ZONE2
followed by
MUTING
.