Onkyo TX SR674 Owner Manual - Page 47

Changing the Input Display, Minimum Speaker Impedance not, North American models

Get Onkyo TX SR674 - 7.1 Channel Up-Converting A/V Receiver PDF manuals and user guides
UPC - 751398007118
View all Onkyo TX SR674 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

First Time Setup-Continued Changing the Input Display If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or next generation HDD-compatible component to the TAPE IN/OUT or VIDEO 3 IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1, 2 1, 2 iPod photo: If you're using an iPod photo with the DS-A1 Remote Interactive Dock, connect the DS-A1 to the VIDEO 3 IN jacks. 1 TAPE Press the [TAPE] or [VIDEO 3] input selector button so that "TAPE" or "VIDEO 3" appears on the display. VIDEO 3 Minimum Speaker Impedance (not North American models) If you change this setting, you must run the automatic speaker setup again (see page 38). If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. Note: Before you change this setting, turn down the volume. 1 RECEIVER Press the [RECEIVER] button, followed by the [SETUP] button. The main menu appears onscreen. SETUP 2 Use the Up and Down [ ]/[ ] buttons to select "8. Hardware Setup," and then press [ENTER]. The Hardware Setup menu appears. 8.Hardware Setup a.SP Impedance :6ohms b.PoweredZone2:NotAct c.TV Format :Auto d.AM Freq. Step: 9kHz e.Remote ID :1 f.HDMI Audio Out :Off g.SW Input Sensitivity : 0dB 2 TAPE VIDEO 3 Press and hold down the [TAPE] or [VIDEO 3] input selector button (about 3 seconds) to change the setting. Repeat this step to select MD, CDR, or HDD. For the TAPE input selector, the setting changes in this order: TAPE → MD → CDR → HDD → For the VIDEO 3 input selector, the setting changes in this order: VIDEO 3 ↔ HDD Note: HDD can be selected for the TAPE input selector or VIDEO 3 input selector, but not both at the same time. 3 Use the Up and Down [ ]/[ ] buttons to select "SP Imped- ance," and then use the Left and Right [ ]/[ ] buttons to select: 4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms. 4 Press the [SETUP] button. Setup closes. SETUP Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
47
First Time Setup
—Continued
If you connect an
-capable Onkyo MiniDisc
recorder, CD recorder, or next generation HDD-compat-
ible component to the TAPE IN/OUT or VIDEO 3 IN
jacks, for
to work properly, you must change this
setting.
This setting can only be changed on the AV receiver.
iPod photo:
If you
’
re using an iPod photo with the
DS-A1 Remote Interactive Dock, connect the DS-A1 to
the VIDEO 3 IN jacks.
Note:
HDD can be selected for the TAPE input selector or
VIDEO 3 input selector, but not both at the same time.
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
Note:
Before you change this setting, turn down the volume.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Changing the Input Display
1
Press the [TAPE] or [VIDEO 3]
input selector button so that
“
TAPE
”
or
“
VIDEO 3
”
appears on
the display.
2
Press and hold down the [TAPE]
or [VIDEO 3] input selector but-
ton (about 3 seconds) to change
the setting.
Repeat this step to select MD, CDR, or
HDD.
For the TAPE input selector, the setting
changes in this order:
TAPE
→
MD
→
CDR
→
HDD
For the VIDEO 3 input selector, the set-
ting changes in this order:
VIDEO 3
↔
HDD
1, 2
1, 2
TAPE
VIDEO
3
TAPE
VIDEO
3
→
Minimum Speaker Impedance (not
North American models)
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select
“
8. Hardware
Setup,
”
and then press [ENTER].
The Hardware Setup menu appears.
3
Use the Up and Down [
]/[
]
buttons to select
“
SP Imped-
ance,
”
and then use the Left and
Right [
]/[
] buttons to select:
4 ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
6 ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
4
Press the [SETUP] button.
Setup closes.
If you change this setting, you must run the automatic
speaker setup again (see page 38).
RECEIVER
SETUP
8.Hardware Setup
------------------------
a.SP Impedance :6ohms
b.PoweredZone2:NotAct
c.TV Format
:Auto
d.AM Freq. Step: 9kHz
e.Remote ID
:1
f.HDMI Audio Out :Off
g.SW Input Sensitivity
: 0dB
SETUP