Panasonic AG DVC20 Dv Camcorder - Page 18
<Note>
![]() |
UPC - 791871302958
View all Panasonic AG DVC20 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
Viewfinder displays Display item What is displayed Status causing the display to appear 8 Shutter speed 9 LOW LIGHT warning display : AUDIO sampling frequency display 1/¢¢.¢ 1/100 - 1/2000 SUPER V LOW LIGHT 48k 32k ; Audio level meter display < VTR warning display/voltage warning display REC WARNING SLACK E-¢¢ = FULL AUTO/SCENE FILE display > AWB color temperature fine adjustment amount display ? Zoom display HUMID SERVO RF TAPE NEAR END TAPE END BATT NEAR END BATT END MP TAPE BACKUP BATT EMPTY FULL Filename which has been set AWB+¢¢ Z00 - Z99 @ AWB color temperature display A ATW, AWB channel display B F value display ¢.¢K Ach Bch PRE ATW NC OPEN F2.0 - F16 CLOSE C Gain display 0 - 36dB Displayed when the shutter speed has been set to SYNCHRO SCAN. Displayed when a fixed shutter speed has been set. Displayed when SUPER V (high vertical resolution mode) has been set. Displayed when the brightness has been reduced. Indicates that a frequency of 48 kHz has been selected. Indicates that a frequency of 32 kHz has been selected. With a 1394 input, the input status is displayed. Indicates the audio levels of CH1 and CH2 (see page 27). Indicates the occurrence of an error during recording. Indicates the occurrence of an error caused by the mechanism. Depending on the type of error, the power may be cut off automatically. For details on the codes displayed, refer to "Error codes" (page 40). Indicates that condensation has formed. Servo lock is not engaged during recording or playback. The signal level from the tape has dropped. The tape is nearing its end (there are about 2 minutes left). The tape has stopped at the tape end. The battery is nearly flat. The tape has stopped because the battery is flat. An MP tape has been loaded. The tape is automatically ejected. It is time to replace the backup battery. Displayed when the FULL AUTO switch has been set to ON. Indicates the filenames (8 characters) set for the scene files. The adjustment amount is displayed when ON has been selected as the "COLOR TEMP" setting (see page 36) and the color temperature has been adjusted finely. It is not displayed when OFF is selected or only ATW has been set. Indicates the zoom amount. However, most 1/2-inch size lenses have no zoom position return. In such a case, this item is not displayed even if ON has been selected as the display setting. Indicates the color temperature. The WHITE BAL switch has been set to channel A. The WHITE BAL switch has been set to channel B. The WHITE BAL switch has been set to PRE. The full time auto white balance has been set. Displayed when the lens cable has not been connected. Displayed when the lens iris has been opened. Indicates the lens iris value. Displayed when the lens iris has been closed. This item appears when using a lens equipped with a function that displays the aperture value. Displays the current gain value. D Filter display E Calendar/clock display F Voltage display BAR display FL1 - FL4 FL- Jan-01-01 00:00:00 ¢¢.¢V B Displays the filter position. Displayed when filter has not been set to the proper position. The 24-hour system is used for the clock display. (Month-day-year and hours-minutes-seconds displayed) The input voltage is displayed. The number of "∫" squares serves as a rough guideline to indicate how much battery charge remains. When the battery still has a sufficient charge, four of these squares are displayed. These squares can be displayed except when Type A or Type B has been selected as the setting on the BATTERY sub-menu. (See page 34) 18
![](/manual_guide/products/panasonic-ag-dvc20-dv-camcorder-1fdf2a4/18.png)