Panasonic HC-X1500 HC-X1500 Advanced Operating Manual - Page 160
Output and Screen Display, Screen status display, Luminance of Y GET
View all Panasonic HC-X1500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 160 highlights
Chapter 7 Output and Screen Display - Screen status display 6 Remaining recording capacity and status of the memory card Displays the remaining recording capacity and status of the memory card in card slot 1 or card slot 2. ≥ [0min] to [999min]: Remaining recording capacity (999 minutes or more is displayed as [999min]) j The display will flash when the remaining recording capacity becomes 2 minutes or less. j The recording capacity available for simultaneous recording (recording capacity for the memory card of the 2 memory cards with less recording capacity) is displayed when simultaneous recording is performed. ≥ [WP]: Write protected (the write protection switch of the memory card is set to the LOCK side) ≥ [END]: No remaining recording capacity (no remaining recording capacity on the memory card) ≥ [ERR]: A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory card being inserted, etc.) ≥ [!SDXC]: An SDXC memory card is not inserted in MOV recording/MP4 recording ≥ (No display): It is in one of the following conditions. j A memory card has not been inserted. j The memory card cannot be recognized. 7 External equipment recording operation control status (/ terminal) Displays the control status of the recording start and recording stop on the external equipment connected to the terminal and the terminal. ≥ [ SDI]*1: Recording instruction is output to the output from the terminal. ≥ [SDI]*1: Pause instruction is output to the output from the terminal. ≥ [ HDMI]: Recording instruction is output to the output from the terminal. ≥ [HDMI]: Pause instruction is output to the output from the terminal. 8 Special recording function Displays the status of special recording function. ≥ [INTRVL]: The interval recording is stopped. ≥ [I-REC]: The interval recording is in progress. (Displayed in red) 9 2-slot function Displays the setting status of the recording function using 2 memory cards. It is displayed with a slanted line if it is in a condition that cannot perform 2-slot recording even if each function is enabled. ≥ [RELAY]: When the relay recording is enabled ≥ [SIMUL]: When the simultaneous recording is enabled ≥ [BACKGR]: When the background recording is enabled ≥ (No display): During standard recording 10 Flash band compensation function ≥ [FBC]: Displayed when the flash band compensation function is operating. 11 Streaming status Displays the streaming status. ≥: When the unit is connected to a device to receive the streaming video, and the streaming video is distributed ≥ (flashing): When the unit is being connected to a device to receive the streaming video ≥: When the streaming function is enabled, it is in condition to operate properly, and the streaming video is not distributed ≥: When there is an error in the streaming function and cannot operate ≥ (No display): When the streaming function is disabled 12 Dynamic range stretcher function ≥ [DRS]: Displays when the dynamic range stretcher function is working. 13 Connection status of the wireless LAN Displays the connection status of the wireless LAN. ≥ : When set to the wireless LAN and the ROP is not connected ≥ : When set to the wireless LAN and the ROP is connected ≥ : When set to the wireless LAN and the wireless LAN is not operating properly ≥ (No display): When the wireless LAN is disabled 14 Power status : Displays the remaining battery level while powered with the battery. (The battery status display will change as → → → → → while the remaining battery level gets lower. It will flash in red when the remaining battery level is zero.) : Displayed when powered with the AC adaptor. 15 Audio level meter Displays the audio level meter. A white border is displayed in the position of the recording base level (12 dB). ≥ : Displayed when audio cannot be recorded. (When super slow is enabled, etc.) 16 Luminance of Y GET Displays the luminance level in 0% through 109% when the Y GET function is operating. 17 Gain Displays the gain value. ≥ [AGC]: Displayed when the auto gain control is operating. ≥ [SG]: Displayed when [SUPER GAIN] is working. ≥ [SGi]: Displayed when [SUPER GAINi] is working. - 160 -