Panasonic PTDZ8700U PTDS8500U User Guide - Page 76

Cooling Condition, Lamp Select, Lamp Relay, Press ▲▼ To Select [lamp Select].

Get Panasonic PTDZ8700U - DLP PROJECTOR PDF manuals and user guides
UPC - 885170010963
View all Panasonic PTDZ8700U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

PROJECTOR SETUP menu COOLING CONDITION You can control the fan speed for projecting angle. When the projector is angled, [COOLING CONDITION] setting must be set correctly. Failure to observe this may result in malfunctions, or the life of the lamp or the other components may be shortened. 1111 Press ▲▼ to select [COOLING CONDITION]. 2222 Press button. zzThe [COOLING CONDITION] screen will be displayed. 3333 Press ▲▼ to select cooling condition. 4444 Press button. 5555 When the confirmation message is displayed, select [OK] or [CANCEL]. VERTICAL UP SETTING FLOOR SETTING 30° 30° 30° 30° CEILING SETTING VERTICAL DOWN SETTING LAMP SELECT You can select a lamp lighting pattern for using environment. 1111 Press ▲▼ to select [LAMP SELECT]. 2222 Press ◄► to switch [LAMP SELECT]. zzThe setting will change as follows each time ◄► is pressed. DUAL SINGLE LAMP2 LAMP1 DUAL SINGLE LAMP1 LAMP2 All lamps will light. Selects a lamp with shorter duration of use. Selects the Lamp unit 1. Selects the Lamp unit 2. 3333 Press button. Note zzIf, in the [SINGLE], [LAMP1] or [LAMP2] mode, one lamp remains off or the currently active lamp exceeds 3 000 hours of cumulative operating time (when [HIGH] is selected as the [LAMP POWER] setting), the other lamp will light. If, in the [DUAL] mode, one lamp remains off or the currently active lamp exceeds 3 000 hours of cumulative operating time (when [HIGH] is selected as the [LAMP POWER] setting), the other lamp alone will light. However, if both lamps remain off or the 3 000 hours of cumulative operating time (when [HIGH] is selected as the [LAMP POWER] setting) are exceeded, the projector will enter the standby mode. zzThe colors of the items indicate the status. Green→Current setting Yellow→Current setting (when a lamp fails or fails to light) Red→Lamp that has failed to light White→Any other status zzIf the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently. LAMP RELAY If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use. 1111 Press ▲▼ to select [LAMP RELAY]. 2222 Press button. zzThe [LAMP RELAY] screen is displayed and the adjustment mode (flashing) is activated. 3333 Press ◄► to select [HOUR] or [MINUTE] and use ▲▼ to adjust the time. 4444 Press button. zzThe lamp relay is set to the selected time. OFF Û 00 : 59 (Unit: 1 hour or 1 minute) 00 : 00 00 : 01 ½½½ When setting the [MINUTE], irrespective of the set value for [HOUR], please adjust and set in the following order of 59 minutes, [OFF], 00 minutes. Settings 76 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
PROJECTOR SETUP menu
76
- ENGLISH
Settings
COOLING CONDITION
You can control the fan speed for projecting
angle. When the projector is angled, [COOLING
CONDITION] setting must be set correctly. Failure to
observe this may result in malfunctions, or the life of
the lamp or the other components may be shortened.
Press ▲▼ to select [COOLING
1 )
CONDITION].
Press <ENTER> button.
2 )
The [COOLING CONDITION] screen will be
z
displayed.
Press ▲▼ to select cooling condition.
3 )
Press <ENTER> button.
4 )
When the confirmation message is
5 )
displayed, select [OK] or [CANCEL].
LAMP SELECT
You can select a lamp lighting pattern for using
environment.
Press ▲▼ to select [LAMP SELECT].
1 )
Press ◄► to switch [LAMP SELECT].
2 )
The setting will change as follows each time
z
◄► is pressed.
DUAL
SINGLE
LAMP2
LAMP1
DUAL
All lamps will light.
SINGLE
Selects a lamp with shorter duration
of use.
LAMP1
Selects the Lamp unit 1.
LAMP2
Selects the Lamp unit 2.
Press <ENTER> button.
3 )
Note
If, in the [SINGLE], [LAMP1] or [LAMP2] mode, one lamp
z
remains off or the currently active lamp exceeds 3 000
hours of cumulative operating time (when [HIGH] is
selected as the [LAMP POWER] setting), the other lamp
will light.
If, in the [DUAL] mode, one lamp remains off or the
currently active lamp exceeds 3 000 hours of cumulative
operating time (when [HIGH] is selected as the [LAMP
POWER] setting), the other lamp alone will light.
However, if both lamps remain off or the 3 000 hours of
cumulative operating time (when [HIGH] is selected as
the [LAMP POWER] setting) are exceeded, the projector
will enter the standby mode.
The colors of the items indicate the status.
z
Green→Current setting
Yellow→Current setting
(when a lamp fails or fails to light)
Red→Lamp that has failed to light
White→Any other status
If the projector is repeatedly used for short periods of
z
time, the lamps will need to be replaced more frequently.
LAMP RELAY
If using the projector for a continuous period of
24 hours or more, this setting can be used to
automatically switch the lamps that are turned on in
order to reduce the lamp deterioration that can occur
as a result of continuous use.
Press ▲▼ to select [LAMP RELAY].
1 )
Press <ENTER> button.
2 )
The [LAMP RELAY] screen is displayed and the
z
adjustment mode (flashing) is activated.
Press ◄► to select [HOUR] or
3 )
[MINUTE] and use ▲▼ to adjust the
time.
Press <ENTER> button.
4 )
The lamp relay is set to the selected time.
z
OFF
Û
00 : 00
00 : 59
00 : 01
When setting the [MINUTE], irrespective of the
:
Û
set value for [HOUR], please adjust and set in the
following order of 59 minutes, [OFF], 00 minutes.
CEILING
SETTING
30°
30°
VERTICAL DOWN
SETTING
30°
30°
VERTICAL UP
SETTING
FLOOR
SETTING
(Unit: 1 hour or
1 minute)