Panasonic WJ-NV300 Installation Guide - Page 42
Camera status], New] button, Addition] button, Camera], Model], Results]
View all Panasonic WJ-NV300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 42 highlights
Note: • Before the settings, register the cameras into the net- work. Only the cameras added by license registration will be detected even though more cameras than the registered license number are connected. It is recommended to disconnect unnecessary cameras. • Cameras shall be connected to the Camera/PC port. Cameras will not be detected if they are connected to the PC port. [New] button Detects all the connected cameras. The models and results of the detected cameras will be displayed. Make sure that the model numbers of all the connected cameras are being displayed. [Addition] button Detects only the added or replaced cameras. The models and results of the detected cameras will be displayed. Make sure that the model numbers of all the added or replaced cameras are being displayed. Important: • The system will assign new IP addresses to all the con- nected cameras (including currently-operated cameras) by clicking [New] button. • Cameras newly added after the operation start will be registered in the default settings. To conform the settings to those of the registered cameras, perform the settings for the added cameras. • For the video encoder (WJ-GXE500), only the camera connected to CH1 will be detected. The channels CH2 to CH4 are needs to be registered from the setup menu. [Camera] Up to 32 cameras can be connected. After the license is registered (☞ page 36), 16, 24 or 32 cameras can be connected. [Model] When Panasonic cameras are used, the model numbers will be displayed. [Results] New: Displayed when the camera is newly connected to the recorder. Replaced: Displayed when the camera has been replaced by another one. Added: Displayed when the camera connection is added to the recorder. Registered: Displayed when the camera has already been registered. Lost: Displayed when the registered camera is not detected. Blank: No camera is detected. Note: • If "Lost" is displayed or the column is left blank, check if the power of the camera is turned on, and make sure that cables are properly connected. 42 Step 6 Click the [Next] button. →→ IP address will be given to the cameras newly con- nected, replaced or added, and the images from the camera will be displayed on the operational screen. Note: • On "Easy Start", it is impossible to register the cameras in other subnets via the same router. • For the security enhancement, changing of the IP address of the camera will become impossible when 20 minutes have passed after the power is turned on. Perform the camera detection within 20 minutes, or turn off the power of the camera and turn it on again if more than 20 minutes has passed. Refer to the operating instructions of the camera for further information. When 20 minutes have passed after the power of the camera is turned on, "ONVIF" may be detected depending on the models of Panasonic cameras. In such a case, turn off the power of the camera and turn if on again to perform the camera detection. • When "On" is selected for the "DHCP" setting of the detected cameras, the recorder will forcibly change the setting to "Off" to give the IP addresses automatically. • When the [Cancel] button is clicked, the top screen of "Easy Start" (the menu to set the date & time) without applying the camera detection result will be displayed. Step 7 When you wish to change the registered camera numbers, it is possible to change the order of the camera numbers. Images from the cameras will be displayed on the monitor from the upper left corner to the right in order of the camera number (1, 2 ... 16: The monitor screen will change according to the number of the camera in use; 9 cameras on 9-screen, 16 cameras on 16-screen, and 24 or 32 cameras on 2 of 16-screen) To interchange camera numbers, drag the camera image to be moved with the mouse and drop on the desired position. If the camera titles are to be interchanged as well, mark the "Also change camera titles" checkbox. [Camera status] The model numbers and statuses of each camera will be displayed in a list. Displaying image: Displays the images from the camera using the IP address that is newly registered or that has already been registered. Changing IP address: Images are being obtained from the camera whose IP address has been changed.