Pioneer SC-99 Owner s Manual - Page 128

13 FAQ Symptom Cause The USB memory cannot be - operated with the remote control. Over Current shows in the - display. Remedy Press iPod USB to set the remote control to the iPod USB control mode. There is a problem with the power supply for the USB memory. After turning off the receiver, disconnect the USB memory, connect the USB memory again and then turn on the power of the receiver. If Over Current is displayed even though the above operation is repeated several times, there is a problem with the receiver or USB memory. Disconnect the power cable and request repair. iPod Symptom iPod is not recognized. iPod touch/iPhone is not recognized or otherwise does not operate properly. iPod cannot be operated with the remote control. No audio is output when operating from an iPod. Cause This receiver recognizes the iPod as a fraud. The iPod's operation may be unstable. - - Remedy Switch off and on again this receiver. Reconnect the iPod with the receiver switched off. Change to an input other than iPod/USB, then set the input back to iPod/USB. Try performing the operation below. 1. Press the sleep/sleep cancel button on the iPod touch/ iPhone simultaneously with the home button for at least 10 seconds to restart the device. 2. Turn this receiver's power on. 3. Connect the iPod touch/iPhone to this receiver. Press iPod USB to set the remote control to the iPod USB control mode. Press iPod iPhone DIRECT CONTROL on the front panel, to switch to iPod operation. Network Symptom Cause Cannot access the network. The LAN cable is not firmly connected. The router is not switched on. Internet security software is currently installed in the connected component. The audio component on the network which has been switched off is switched on. Fails Wireless Accessory Configuration. iOS equipment is not connected to the Wi-Fi equipment. Playback does not start while "Connecting..." continues to be displayed. The component is currently disconnected from this receiver or the power supply. Remedy Firmly connect the LAN cable (page 47) . Switch on the router. There are cases where a component with Internet security software installed cannot be accessed. Switch on the audio component on the network before switching on this receiver. Connect the iOS equipment to Wi-Fi. Check whether the component is properly connected to this receiver or the power supply. Symptom The network function cannot be operated with the remote control. The PC or Internet radio is not properly operated. The audio files stored on components on the network, such as a PC, cannot be played back. Cannot access the component connected to the network. Cause - Remedy Press NET to set the remote control to the network function control mode. The corresponding IP address is not properly set. Switch on the built-in DHCP server function of your router, or set up the network manually according to your network environment (page 53 ). The IP address is being automatically configured. The automatic configuration process takes time. Please wait. Windows Media Player 11 or Windows Media Player 12 is not currently installed on your PC. Install Windows Media Player 11 or Windows Media Player 12 on your PC (page 78 ). The audio file currently being played back was not recorded in a format playable on this receiver. Audio files recorded in MPEG-4 AAC or FLAC cannot be played back on Windows Media Player 11 or Windows Media Player 12. Try using another server. Refer to the operation manual supplied with your server. The component connected to the network is not properly operated. Check whether the component is affected by special circumstances or is in the sleep mode. Try rebooting the component if necessary. The component connected to the Try changing the settings for the component connected to network does not permit file sharing. the network. The folder stored on the component connected to the network has been deleted or damaged. Check the folder stored on the component connected to the network. Network connections could be Check the computer's network settings, security settings, etc. restricted due to the computer's net- work settings, security settings, etc. Supported file formats vary by server. For more information check with the manufacturer of your As such, files not supported by your server. server are not displayed on this unit. The audio files are copyrighted. DRM-protected audio files cannot be played back on this receiver. The component connected to the network is not properly set. If the client is automatically authorized, you need to enter the corresponding information again. Check whether the connection status is set to "Do not authorize". There are no playable audio files on the component connected to the network. Check the audio files stored on the component connected to the network. 128