Pioneer SC-99 Owner s Manual - Page 97

Standby/on.

Get Pioneer SC-99 PDF manuals and user guides View all Pioneer SC-99 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

09 Using other functions Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. Set MULTI-ZONE to MULTI ZONE OFF. ! Disconnect the iPod and USB memory device from the receiver beforehand. ! Set the Control with HDMI to OFF (see HDMI Setup on page 85 ). 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press u STANDBY/ON. The display shows RESET c NO d. 3 Select 'RESET' using PRESET k/l, then press ENTER on the front panel. The display shows RESET? OK. 4 Press ENTER to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. ! Note that all settings will be saved, even if the receiver is unplugged. Default system settings Setting SPEAKERS Speaker System Front Center TMd/TFw/TBw Speaker Setting FH/FW Surr SB SW Crossover X-Curve DIMMER Inputs See Input function default and possible settings on page 61. Input Volume Absorber All Inputs HDMI HDMI Audio Control Control Mode ARC (Audio Return Channel) PQLS Standby Through 4K/60pBD 4K/60pH1 (HDMI IN 1) 4K/60pH2 (HDMI IN 2) Default ON 7.2.2/5.2.2/7.2ch SMALL SMALL SMALL SMALL SMALL SMALLx2 SW1+2 YES 80Hz OFF Brightest 0dB AMP OFF --- (OFF) --- (OFF) --- (AUTO) OFF 4:2:0 4:2:0 4:2:0 Setting DSP Power On Level Volume Limit Mute Level Phase Control Auto Sound Retriever Sound Delay Dual Mono DRC LFE Attenuate Auto delay Digital Safety Effect Level Center Spread iPod/USB, INTERNET RADIO, PANDORA, Spotify, MEDIA SERVER, FAVORITES, BT AUDIO input function Other input functions ALC (Auto Level Control) Neo:X Options Center Gain All Inputs Listening Mode (2 ch/multi ch) Listening Mode (Headphones) See also Setting the Audio options on page 89 for other default DSP settings. MCACC MCACC Position Memory Channel Level (M1 to M6) Speaker Distance (M1 to M6) Standing Wave (M1 to M6) ATT of all channels/filters SWch Wide Trim EQ Data (M1 to M6) All channels/bands EQ Wide Trim Network Network Standby DHCP Default LAST OFF FULL ON ON OFF 0 ms CH1 OFF 0dB OFF OFF 50 OFF Neo:X CINEMA: 1.0 Neo:X MUSIC: 0.3 Neo:X GAME: 1.0 AUTO SURROUND STEREO M1. MEMORY 1 0.0 dB 10'00'' 0.0 dB 0.0 dB 0.0 dB 0.0 dB ON ON 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
97
Using other functions
09
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to
MULTI ZONE OFF
.
!
Disconnect the iPod and USB memory device from the receiver beforehand.
!
Set the
Control
with HDMI to
OFF
(see
HDMI Setup
on
page 85
).
1
Switch the receiver into standby.
2
While holding down ENTER on the front panel, press
u
STANDBY/ON.
The display shows
RESET
c
NO
d
.
3
Select ‘RESET’ using PRESET
k
/
l
, then press ENTER on the front panel.
The display shows
RESET? OK
.
4
Press ENTER to confirm.
OK
appears in the display to indicate that the receiver has been reset to the factory default settings.
!
Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting
Default
SPEAKERS
ON
Speaker System
7.2.2/5.2.2/7.2ch
Speaker Setting
Front
SMALL
Center
SMALL
TMd/TFw/TBw
SMALL
FH/FW
SMALL
Surr
SMALL
SB
SMALLx2
SW
SW1+2 YES
Crossover
80Hz
X-Curve
OFF
DIMMER
Brightest
Inputs
See
Input function default and possible settings
on
page 61
.
Input Volume Absorber
All Inputs
0dB
HDMI
HDMI Audio
AMP
Control
OFF
Control Mode
---
(OFF)
ARC (Audio Return Channel)
---
(OFF)
PQLS
---
(AUTO)
Standby Through
OFF
4K/60pBD
4:2:0
4K/60pH1 (HDMI IN 1)
4:2:0
4K/60pH2 (HDMI IN 2)
4:2:0
Setting
Default
DSP
Power On Level
LAST
Volume Limit
OFF
Mute Level
FULL
Phase Control
ON
Auto Sound Retriever
iPod/USB, INTERNET RADIO, PANDORA,
Spotify, MEDIA SERVER, FAVORITES, BT
AUDIO input function
ON
Other input functions
OFF
Sound Delay
0
ms
Dual Mono
CH1
DRC
OFF
LFE Attenuate
0dB
Auto delay
OFF
Digital Safety
OFF
Effect Level
ALC (Auto Level Control)
50
Center Spread
OFF
Neo:X Options
Center Gain
Neo:X CINEMA:
1.0
Neo:X MUSIC:
0.3
Neo:X GAME:
1.0
All Inputs
Listening Mode (2 ch/multi ch)
AUTO SURROUND
Listening Mode (Headphones)
STEREO
See also
Setting the Audio options
on
page 89
for other default DSP settings.
MCACC
MCACC Position Memory
M1. MEMORY 1
Channel Level (M1 to M6)
0.0 dB
Speaker Distance (M1 to M6)
10’00’’
Standing Wave (M1 to M6)
ATT of all channels/filters
0.0 dB
SWch Wide Trim
0.0 dB
EQ Data (M1 to M6)
All channels/bands
0.0 dB
EQ Wide Trim
0.0 dB
Network
Network Standby
ON
DHCP
ON