Pioneer VSX-1122-K Owner's Manual - Page 89

13 FAQ Professional Calibration EQ graphical output Symptom Remedy The reverb characteristics graph after EQ calibration does not appear entirely flat. There are cases where the graph does not appear flat (even when selecting ALL CH ADJ in the Auto MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound. Areas of the graph may appear identical (before and after) when there is little or no adjustment needed. The graph may appear to have shifted vertically when comparing before and after measurements. EQ adjustments made using the Manual MCACC setup do not appear to change the reverb characteristics graph after EQ calibration. Despite level adjustments being made, the filters used for analysis may not display these adjustments in the reverb characteristics graph after EQ calibration. However, these adjustments are taken into account by the filters dedicated to overall system calibration. Lower frequency response curves do Low frequencies used in bass management (the subwoofer channel) will not change for not seem to have been calibrated for speakers that have been specified as SMALL in the configuration, or do not output these SMALL speakers. frequencies. Calibration is performed, but due to your speakers' low frequency limitations, no measurable sound is output for display. Display Symptom Remedy The display is dark or off. Press DIMMER repeatedly to select a different brightness. The OSD screen is not displayed. The OSD screen is not displayed unless the receiver and TV are connected using an HDMI cable. If the TV does not support HDMI, perform the various operations and make the settings while watching the display on the receiver's front panel. You can't get DIGITAL to display when using SIGNAL SEL. Check the digital connections and make sure that the digital inputs are assigned correctly (see The Input Setup menu on page 35). 2 DIGITAL or DTS does not light when playing Dolby/DTS software. These indicators do not light if playback is paused. Check the playback (especially the digital output) settings of the source component. When playing Dolby Digital or DTS Check that the player is connected using a digital connection. sources, the receiver's format indica- Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on tors do not light. page 46). Check that the player isn't set up so that Dolby Digital and DTS sources are converted to PCM. Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is selected. When playing certain discs, none of The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on the receiver's format indicators light. what audio tracks are recorded on the disc. When playing a disc with the listening mode set to Auto Surround or ALC, 2 Pro Logic II or DTS Neo:6 appear on the receiver. Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 46). If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a malfunction. Check the disc packaging for details about the audio tracks available. During playback of DVD-Audio, the display shows PCM. This will occur when playing DVD-Audio material over the HDMI connection. This is not a malfunction. Symptom Remedy The power turns off automatically and some indicator flashes, or some indicator flashes and the power does not turn on. See the Power section (page 86). Remote control Symptom Remedy Cannot be remote controlled. Set the remote control unit's remote control mode so that it matches the setting on the main unit (see Operating multiple receivers on page 66). Check whether the receiver's remote control mode is properly set (see Remote Control Mode Setup on page 84). Try replacing the batteries in the remote control (see Loading the batteries on page 8). Be sure to operate within 7 m (23 ft.) and a 30º angle of the remote sensor on the front panel (see Operating range of remote control unit on page 8). Check that there are no obstacles between the receiver and the remote control. Make sure that there is no fluorescent or other strong light shining on to the remote sensor. Other components can't be operated If the battery ran down, the preset codes may have been cleared. Re-enter the preset with the system remote. codes. The preset code may be incorrect. Redo the procedure for entering preset codes. When commands from the remote control units of other devices are registered using the learning function, in some cases they may not be learned properly. In this case, register the commands again using the learning function (see page 67). If they still do not work, they may be in a special format that cannot be registered on this receiver's remote control. Operate the device using another remote control. HDMI Symptom The HDMI indicator blinks continuously. No picture or sound. Remedy Check all the points below. This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-compatible. If they are not, please connect them using the component or composite video jacks. Depending on the connected source component, it's possible that it will not work with this receiver (even if it is HDCP-compatible). In this case, connect using the component or composite video jacks between source and receiver. If the problem still persists when connecting your HDMI component directly to your monitor, please consult the component or monitor manual or contact the manufacturer for support. If video images do not appear on your TV, try adjusting the resolution, Deep Color or other setting for your component. While analog video signals are being output over HDMI, use a separate connection for audio output. To output signals in Deep Color, use an HDMI cable (High Speed HDMI® Cable) to connect this receiver to a component or TV with the Deep Color feature. 89