Poulan PP105G30 Rider Operation Manual - Page 27

PARTES NO ENSAMBLADAS Inserto del volante de dirección Volante de dirección Accesorio de transción de la dirección (1) Parachoques traseros (1) 5/16-18 x 4 Perno de cabeza hexagonal (1) Arandela de seguridad Cobertura Eje de Extención Adaptador (1) Arandela (1) Parachoques delanteros Asiento (1) Arandela (1) Perno (2) Llave Hoja de pendiente 34 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to an authorized service center. PROBLEM Will not start Hard to start Engine will not turn over Engine clicks but will not start Loss of power Excessive vibration Engine continues to run when operator leaves seat with attachment clutch engaged CAUSE CORRECTION 1 Out of fuel. 2 Bad spark plug. 3 Dirty air filter. 4 Water in fuel. 5 Loose or damaged wiring. 6 Engine valves out of adjustment. 1 Fill fuel tank. 2 Replace spark plug. 3 Clean/replace air filter. 4 Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 5 Check all wiring. 6 Contact a qualified service center. 1 Dirty air filter. 2 Bad spark plug. 3 Weak or dead battery. 4 Stale or dirty fuel. 5 Loose or damaged wiring. 6 Engine valves out of adjustment. 1 Clean/replace air filter. 2 Replace spark plug. 3 Recharge or replace battery. 4 Empty fuel tank and refill tank with fresh, clean gasoline. 5 Check all wiring. 6 Contact a qualified service center. 1 Clutch/brake pedal not depressed. 1 Depress clutch/brake pedal. 2 Deck clutch is engaged. 2 Disengage deck clutch. 3 Weak or dead battery. 3 Recharge or replace battery. 4 Blown fuse. 4 Replace fuse. 5 Corroded battery terminals. 5 Clean battery terminals. 6 Loose or damaged wiring. 6 Check all wiring. 7 Faulty ignition switch. 7 Check/replace ignition switch. 8 Faulty solenoid or starter. 8 Check/replace solenoid or starter. 9 Faulty operator presence switch(es). 9 Contact a qualified service center. 1 Weak or dead battery. 2 Corroded battery terminals. 3 Loose or damaged wiring. 4 Faulty solenoid or starter. 1 Recharge or replace battery. 2 Clean battery terminals. 3 Check all wiring. 4 Check/replace solenoid or starter. 1 Cutting too much grass/too fast. 2 Build-up of grass, leaves and trash under mower. 3 Dirty air filter. 4 Low oil level/dirty oil. 5 Faulty spark plug. 6 Stale or dirty fuel. 7 Water in fuel. 8 Spark plug wire loose. 9 Dirty engine air screen/fins. 10 Dirty/clogged muffler. 11 Loose or damaged wiring. 12 Engine valves out of adjustment. 1 Raise cutting height/reduce speed. 2 Clean underside of mower housing. 3 Clean/replace air filter. 4 Check oil level/change oil. 5 Clean & regap or change spark plug. 6 Empty fuel tank and refill tank with fresh, clean gasoline. 7 Empty fuel tank and carburetor, refill tank with fresh gasoline. 8 Connect & tighten spark plug wire. 9 Clean engine air screen/fins. 10 Clean/replace muffler. 11 Check all wiring. 12 Contact a qualified service center. 1 Worn, bent or loose blade. 2 Bent blade mandrel. 3 Loose/damaged part(s). 1 Replace blade. Tighten blade bolt. 2 Contact a qualified service center. 3 Tighten loose part(s). Replace damaged parts. 1 Faulty operator-safety presence control 1 Check wiring, switches and system. connections. If not corrected, contact a qualified service center. CAUTION: DO NOT operate machine until problem is corrected. 27