Schwinn IC3 Indoor Cycling Bike Service Manual - Page 29

holes in the Brake Assembly arm are slots to let you adjust the position

Get Schwinn IC3 Indoor Cycling Bike PDF manuals and user guides View all Schwinn IC3 Indoor Cycling Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Disconnect the data cable from the console before you service this machine. Note: Your machine may not match the image. For reference only. . HHSWKHÀ\ZKHHOVWDEOHGXULQJWKLVSURFHGXUH 'RQRWWXUQWKHFUDQNDUPV)O\ZKHHOPRYHPHQW FDQSXOO¿QJHUVLQDQGFDXVHLQMXU\ 1. Using a #2 Phillips screwdriver, loosen and remove the hardware that attaches the Fender to the Main Frame. Set the Fender and hardware safely aside for reassembly. NOTICE: Hold the Fender so that it does not fall. 2. Carefully remove the Fender and set it safely aside for reassembly. NOTICE: Do not crimp the cable. 3. Loosen the Resistance Knob (A) to the minimum resistance setting. 4. Using a 10mm open end wrench, loosen the hardware (B1) that attaches the Brake Assembly (B) to the Frame Mount (C). The screw holes in the Brake Assembly arm are slots to let you adjust the position of the arm on the Frame Mount. 5. Remove the old Brake Assembly (B) and set it safely aside. If you are not replacing the Resistance Knob assembly- go to step 11. Installation of the new Brake Assembly is the reverse procedure. 29 A % C %

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
29
Note:
Your machine may not match the image. For reference only.
.HHS WKH À\ZKHHO VWDEOH GXULQJ WKLV SURFHGXUH³
'R QRW WXUQ WKH FUDQN DUPV³ )O\ZKHHO PRYHPHQW
FDQ SXOO ¿QJHUV LQ DQG FDXVH LQMXU\³
1.
Using a #2 Phillips screwdriver, loosen and remove the hardware
that attaches the Fender to the Main Frame. Set the Fender and hardware
safely aside for reassembly.
NOTICE:
Hold the Fender so that it does not fall.
2.
Carefully remove the Fender and set it safely aside for reassembly.
NOTICE:
Do not crimp the cable.
3.
Loosen the Resistance Knob (A) to the minimum resistance setting.
4.
Using a 10mm open end wrench, loosen the hardware (B1) that
attaches the Brake Assembly (B) to the Frame Mount (C). The screw
holes in the Brake Assembly arm are slots to let you adjust the position of
the arm on the Frame Mount.
5
. Remove the old Brake Assembly (B) and set it safely aside.
If you are not replacing the Resistance Knob assembly— go to step 11.
Installation of the new Brake Assembly is the reverse procedure.
Disconnect the data cable from the console before you service this machine.
A
%
%¸
C