Schwinn IC3 Indoor Cycling Bike Service Manual - Page 52

Put the Drive Belt P around the edge of the Drive Pulley Q. Slowly

Get Schwinn IC3 Indoor Cycling Bike PDF manuals and user guides View all Schwinn IC3 Indoor Cycling Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

18. $OLJQWKH)O\ZKHHOD[OH - LQWKHÀ\ZKHHOEUDFNHWV + +DQGWLJKWHQ the hardware from steps 11 and 12 on each end of the Flywheel axle. NOTICE: Do not crimp any cables. 19. Put the Drive Belt (P) around the edge of the Drive Pulley (Q). Slowly turn the Drive Pulley and carefully walk the Drive Belt onto the Drive Pulley. Make sure the Drive Belt is aligned on the Flywheel pulley (L1) and Drive Pulley. %HVXUHWRNHHS¿QJHUVFOHDURIDOOSLQFK KD]DUGVDV\RXWXUQWKH'ULYH3XOOH\ 4 DQG Flywheel (L). 20. Reassembly is the reverse procedure. NOTICE: Do not crimp any cables. Install the Flywheel Tensioners (G) at the position that you recorded in step 10. Make sure the Flywheel (L) can turn easily. Verify that the Speed Sensor (N) and Speed Sensor Magnet (R) on the Flywheel do not touch. Installation does not require the use of the crank puller. Be sure the Crank Arms are connected at 180° from each other. 21. Make sure that the Drive Belt tension is correct. Refer to the "Adjust the Belt Tension" procedure. 22. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner's Manual. N R 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
52
18.
$OLJQ WKH )O\ZKHHO D[OH ¶-· LQ WKH À\ZKHHO EUDFNHWV ¶+·´ +DQG WLJKWHQ
the hardware from steps 11 and 12 on each end of the Flywheel axle.
NOTICE:
Do not crimp any cables.
19.
Put the Drive Belt (P) around the edge of the Drive Pulley (Q). Slowly
turn the Drive Pulley and carefully walk the Drive Belt onto the Drive
Pulley. Make sure the Drive Belt is aligned on the Flywheel pulley (L1) and
Drive Pulley.
%H VXUH WR NHHS ¿QJHUV FOHDU RI DOO SLQFK
KD]DUGV DV \RX WXUQ WKH 'ULYH 3XOOH\ ¶4² DQG
Flywheel (L).
20.
Reassembly is the reverse procedure.
NOTICE:
Do not crimp any cables. Install the Flywheel Tensioners
(G) at the position that you recorded in step 10. Make
sure the Flywheel (L) can turn easily. Verify that the
Speed Sensor (N) and Speed Sensor Magnet (R) on the
Flywheel do not touch.
Installation does not require the use of the crank puller. Be sure the Crank
Arms are connected at 180° from each other.
21.
Make sure that the Drive Belt tension is correct. Refer to the “Adjust
the Belt Tension” procedure.
22.
Final Inspection
Inspect your machine to ensure that all hardware is tight and components
are properly assembled.
Do not use until the machine has been fully
assembled and inspected for correct
performance in accordance with the Owner’s
Manual.
N
R