Schwinn IC3 Indoor Cycling Bike Service Manual - Page 38

Pedal not shown

Get Schwinn IC3 Indoor Cycling Bike PDF manuals and user guides View all Schwinn IC3 Indoor Cycling Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

NOTICE: At the end of this procedure, make sure that the Drive Chain tension is correct. Refer to the "Adjust the Chain Tension" procedure. Disconnect the data cable from the console before you service this machine. Note: Your machine may not match the image. For reference only. 1. 8VLQJDÀDWKHDGVFUHZGULYHUUHPRYHWKHWKUHDGHG&DS % IURPWKH right Crank Arm (A). 2. Using a 16mm socket and wrench, remove the Flange Nut (C) under the threaded Cap (B). % A Pedal not shown A 3. Thread the Crank Puller into the Crank Arm (A). When the Crank Puller is in the correct position, only 1-2 threads on the outer portion (CP2) C of the Crank Puller should show. Note:%HVXUHWKHHQGRIWKH%ROW &3 LQWKH&UDQN3XOOHULVÀXVK with the inner surface (CP2) as shown, before use. 4. Using a 15mm wrench, turn the inner portion (CP3) of the Crank Puller clockwise. The Crank Arm (A) will slide off as it is tightened. CP1 CP2 CP3 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
38
Note:
Your machine may not match the image. For reference only.
1.
8VLQJ D ÀDWKHDG VFUHZGULYHUµ UHPRYH WKH WKUHDGHG &DS ¶%· IURP WKH
right Crank Arm (A).
2.
Using a 16mm socket and wrench, remove the Flange Nut (C) under
the threaded Cap (B).
3.
Thread the Crank Puller into the Crank Arm (A). When the Crank
Puller is in the correct position, only 1-2 threads on the outer portion (CP2)
of the Crank Puller should show.
Note:
%H VXUH WKH HQG RI WKH %ROW ¶&3±· LQ WKH &UDQN 3XOOHU LV ÀXVK
with the inner surface (CP2) as shown, before use.
4.
Using a 15mm wrench, turn the inner portion (CP3) of the Crank
Puller clockwise. The Crank Arm (A) will slide off as it is tightened.
NOTICE:
At the end of this procedure, make sure that the Drive Chain tension is correct. Refer to the “Adjust the Chain Tension” procedure.
Disconnect the data cable from the console before you service this machine.
%
A
C
A
CP1
CP2
CP3
Pedal not shown