Schwinn IC3 Indoor Cycling Bike Service Manual - Page 45

H Vxuh Wr Nhhs ¿qjhuv Fohdu Ri Doo Slqfk

Get Schwinn IC3 Indoor Cycling Bike PDF manuals and user guides View all Schwinn IC3 Indoor Cycling Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

11. To loosen the Flywheel hardware, use a 15 mm crescent wrench to hold the Axle Nut (I) on one side steady and loosen the Axle Nut on the opposite side with a 15 mm socket and wrench. Remove the Axle Nuts from the Flywheel axle (J). Set the Nuts safely aside for reassembly. 12. Using a 10mm wrench, loosen and remove the Flywheel Retainer nut (K1) that is closest to the Frame. Remove the Tensioner eyebolt (G) and Nut (K2) from the Flywheel axle (J) and Tensioner support (H1). Set the Tensioner hardware aside for reassembly. I G + I J 13. &DUHIXOO\PRYHWKH)O\ZKHHO / WRWKHRSHQLQJLQWKHÀ\ZKHHO brackets (H). NOTICE: This step may require two people. 14. Carefully remove the right end of the Flywheel axle (J) from the bracket (H). NOTICE: Make sure to avoid damage to the Speed Sensor (M) on the left end of the Flywheel axle (J). 15. Remove the Drive Belt (N) from the Flywheel pulley (L1) and Drive Pulley (O) to the outside. Set the old Drive Belt safely aside. %HVXUHWRNHHS¿QJHUVFOHDURIDOOSLQFK KD]DUGVDV\RXWXUQWKH'ULYH3XOOH\ 2 DQG Flywheel (L). N O 16. +ROGWKH)O\ZKHHO / QHDUWKHÀ\ZKHHOEUDFNHW + DQGSXWWKHQHZ Drive Belt (N) in position on the Flywheel pulley (L1). NOTICE: This step may require two people. 17. $OLJQWKH)O\ZKHHOD[OH - LQWKHÀ\ZKHHOEUDFNHWV + +DQGWLJKWHQ the hardware from steps 11 and 12 on each end of the Flywheel axle. NOTICE: Do not crimp any cables. M L + J / + J L M J 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
45
11.
To loosen the Flywheel hardware, use a 15 mm crescent wrench to
hold the Axle Nut (I) on one side steady and loosen the Axle Nut on the
opposite side with a 15 mm socket and wrench. Remove the Axle Nuts
from the Flywheel axle (J). Set the Nuts safely aside for reassembly.
12.
Using a 10mm wrench, loosen and remove the Flywheel Retainer
nut (K1) that is closest to the Frame. Remove the Tensioner eyebolt (G)
and Nut (K2) from the Flywheel axle (J) and Tensioner support (H1). Set
the Tensioner hardware aside for reassembly.
13.
&DUHIXOO\ PRYH WKH )O\ZKHHO ¶/· WR WKH RSHQLQJ LQ WKH À\ZKHHO
brackets (H).
NOTICE:
This step may require two people.
14.
Carefully remove the right end of the Flywheel axle (J) from the
bracket (H).
NOTICE:
Make sure to avoid damage to the Speed Sensor (M) on
the left end of the Flywheel axle (J).
15.
Remove the Drive Belt (N) from the Flywheel pulley (L1) and Drive
Pulley (O) to the outside. Set the old Drive Belt safely aside.
%H VXUH WR NHHS ¿QJHUV FOHDU RI DOO SLQFK
KD]DUGV DV \RX WXUQ WKH 'ULYH 3XOOH\ ¶2² DQG
Flywheel (L).
16.
+ROG WKH )O\ZKHHO ¶/· QHDU WKH À\ZKHHO EUDFNHW ¶+· DQG SXW WKH QHZ
Drive Belt (N) in position on the Flywheel pulley (L1).
NOTICE:
This step may require two people.
17.
$OLJQ WKH )O\ZKHHO D[OH ¶-· LQ WKH À\ZKHHO EUDFNHWV ¶+·´ +DQG WLJKWHQ
the hardware from steps 11 and 12 on each end of the Flywheel axle.
NOTICE:
Do not crimp any cables.
I
G
+
J
I
N
/¸
J
O
L
+
M
J
J
M
+
L