Sharp AR M207 AR-M162 AR-M207 Operation Manual Suite - Page 226
Speaker Volume, Tx/rx End Sound, Tx/rx End Sound Length, Extension Tel
View all Sharp AR M207 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 226 highlights
KEY OPERATOR PROGRAMS 5 Enter your fax number with the numeric keys and then press the [OK] key. • If you make a mistake, press the [C] key and re-enter the number. • To enter "+", press the key. 6 Enter your name and then press the [START] key ( ). See "ENTERING CHARACTERS" (page 82) for the procedure for entering letters. Note To clear the programmed fax number and name, follow these steps: (1) Select "DELETE" in step 4 and then press the [OK] key. (2) Select "DELETE" with the [ ] or [ ] key and then press the [OK] key. SPEAKER VOLUME This setting is used to adjust the on-hook volume, the ringing volume, the line monitor volume, the TX/RX end sound volume, the original scanning end sound volume, and the tone output volume. All volume settings are initially set to "MIDDLE". 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key. 3 Select "SPEAKER VOLUME" with the [ ] or [ ] key and then press the [OK] key. 4 Select name of the volume that you wish to adjust with the [ ] or [ ] key and then press the [OK] key. 5 Select the desired volume level with the [ ] or [ ] key and then press the [OK] key. • "HIGH", "MIDDLE" or "LOW" can be selected for the on hook volume. • "HIGH", "MIDDLE", "LOW" or "OFF" can be selected for volumes other than the on hook volume. TX/RX END SOUND This program is used to select the beep pattern that signals the end of transmission or reception. "PATTERN 1", "PATTERN 2" or "PATTERN 3" can be selected. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key. 3 Select "TX/RX END SOUND" with the [ ] or [ ] key and then press the [OK] key. 4 Select "SEND" or "RECEIVE" with the [ ] or [ ] key and then press the [OK] key. 5 Select "PATTERN 1", "PATTERN 2", or "PATTERN 3" with the [ ] or [ ] key and then press the [OK] key. Before pressing the [OK] key to store your selection, you can press the key to listen to the selected pattern. TX/RX END SOUND LENGTH This setting is used to select the length of the end sound in seconds. Selections are "2.0 sec", "2.5 sec", "3.0 sec", "3.5 sec", and "4.0 sec". "3.0 sec" is normally selected. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key. 3 Select "TX/RX END SOUND LENGTH" with the [ ] or [ ] key and then press the [OK] key. 4 Select the number of seconds with the [ ] or [ ] key and then press the [OK] key. EXTENSION TEL Enable this setting when an extension telephone is connected to the machine. An extension telephone connected to the machine cannot be used until this setting is enabled. The initial setting is enabled. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 94). 2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key. 3 Select "EXTENSION TEL" with the [ ] or [ ] key and then press the [OK] key. • The setting is enabled and a checkmark appears in the checkbox. • If this procedure is performed when the setting 8 is enabled, the checkmark will be cleared and the setting disabled. 97