Sharp PN-T322B Service Manual - Page 10

Part Names And Function, Display

Get Sharp PN-T322B PDF manuals and user guides View all Sharp PN-T322B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

CHAPTER 1. OUTLINE OF THE PRODUCT 2. PART NAMES AND FUNCTION 2 - 1. DISPLAY ■ FRONT VIEW 1 1 LCD panel 2 Power LED 3 Power switch 4 Input switch 5 Remote control sensor MEMO n Use a pointed object such as a pen tip to press the switches at the operation panel. 2 3 4 5 REFERENCE CHART OF POWER LAMP LIGHTING STATUS Lighting Status Green lamp is lit. Green lamp is flashing. Orange lamp is lit. Lamp is flashing in red3green3red3green at 1 second intervals. (Temperature abnomaly) Status Description In the power "ON" state In the input signal waiting mode (When DVI-D or D-SUB) In the power "OFF" state (Standby status=The power is turned off by the remote controller.) If the Power switch is pressed when the display is in the input signal waiting mode (green lamp flashing), it also goes into the standby status. The message "TEMPERATURE" blinks at 5-second intervals in the corner of the screen (Lower left corner at the factory default), and it indicates an abnormality in the internal temperature. * It operates only when "FUNCTION" - "TEMPERATURE ALERT" is set to "OSD&LED" or "LED". When it is "OFF", it does not blink. (Factory default: "LED") * Even when "FUNCTION" - "LED" is set to "OFF", the setting of "TEMPERATURE ALERT" takes effect. At the same time, the brightness is forcefully reduced by the internal processing of the LCD monitor. If it is left in the above state and the internal temperature increases further, the monitor shuts off automatically. (Goes into the standby mode.) By cycling the main power or turning off and on the power by the remote controller, the screen can be restored to its original state temporarily. However, it goes back to the standby status soon unless the cause of the temperature increase is removed. PN-T321/T322B OUTLINE OF THE PRODUCT 1 - 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
CHAPTER 1.
OUTLINE OF THE PRODUCT
PN-T321/T322B
OUTLINE OF THE PRODUCT
1 – 6
2.
PART NAMES AND FUNCTION
2 - 1.
DISPLAY
■
FRONT VIEW
MEMO
n
Use a pointed object such as a pen tip to press the switches at
the operation panel.
REFERENCE CHART OF POWER LAMP LIGHTING STATUS
2
3
4
5
1
1
LCD panel
2
Power LED
3
Power switch
4
Input switch
5
Remote control sensor
Lighting Status
Status Description
Green lamp is lit.
In the power “ON” state
Green lamp is flashing.
In the input signal waiting mode (When DVI-D or D-SUB)
Orange lamp is lit.
In the power “OFF” state (Standby status=The power is turned off by the remote controller.)
If the Power switch is pressed when the display is in the input signal waiting mode (green lamp flashing), it also goes
into the standby status.
Lamp is flashing in
red
3
green
3
red
3
green
at 1 second intervals.
(Temperature
abnomaly)
The message “TEMPERATURE” blinks at 5-second intervals in the corner of the screen (Lower left corner at the fac-
tory default), and it indicates an abnormality in the internal temperature.
*
It operates only when “FUNCTION” - “TEMPERATURE ALERT” is set to “OSD&LED” or “LED”.
When it is “OFF”, it does not blink. (Factory default: “LED”)
*
Even when “FUNCTION” - “LED” is set to “OFF”, the setting of “TEMPERATURE ALERT” takes effect.
At the same time, the brightness is forcefully reduced by the internal processing of the LCD monitor.
If it is left in the above state and the internal temperature increases further, the monitor shuts off automatically.
(Goes
into the standby mode.)
By cycling the main power or turning off and on the power by the remote controller,
the screen can be restored to its original
state temporarily.
However, it goes back to the standby status soon unless the cause of the temperature increase is removed.